Lightspeed Attenuator - Best Preamp Ever?


The question is a bit rhetorical. No preamp is the best ever, and much depends on system context. I am starting this thread beacuase there is a lot of info on this preamp in a Music First Audio Passive...thread, an Slagle AVC Modules...thread and wanted to be sure that information on this amazing product did not get lost in those threads.

I suspect that many folks may give this preamp a try at $450, direct from Australia, so I thought it would be good for current owners and future owners to have a place to describe their experience with this preamp.

It is a passive preamp that uses light LEDs, rather than mechanical contacts, to alter resistance and thereby attenuation of the source signal. It has been extremely hot in the DIY community, since the maker of this preamp provided gernerously provided information on how to make one. The trick is that while there are few parts, getting it done right, the matching of the parts is time consuming and tricky, and to boot, most of use would solder our fingers together if we tried. At $450, don't bother. It is cased in a small chassis that is fully shielded alloy, it gets it's RF sink earth via the interconnects. Vibration doesn't come into it as there is nothing to get vibrated as it's passive, even the active led's are immune as they are gas element, no filaments. The feet I attach are soft silicon/sorbethane compound anyway just in case.

This is not audio jewelry with bling, but solidly made and there is little room (if any) for audionervosa or tweaking.

So is this the best preamp ever? It might be if you have a single source (though you could use a switch box), your source is 2v or higher, your IC from pre-amp to amp is less than 2m to keep capaitance low, your amp is 5kohm input or higher (most any tube amp), and your amp is relatively sensitive (1v input sensitivity or lower v would be just right). In other words, within a passive friendly system (you do have to give this some thought), this is the finest passive preamp I have ever heard, and I have has many ranging form resistor-based to TVCs and AVCs.

In my system, with my equipment, I think it is the best I have heard passive or active, but I lean towards prefering preamp neutrality and transparency, without loosing musicality, dynamics, or the handling of low bass and highs.

If you own one, what are your impressions versus anything you have heard?

Is it the best ever? I suspect for some it may be, and to say that for a $450 product makes it stupidgood.
pubul57
Off to the closet to unpack the RM-10.

I light load my RM-10 since my speakers are 12 ohm nominal and don't dip below 8. Anyone else light load their RM-10?
Do you think the 12ohm nominal benefits you with light loading because you lose less power output? I think your "light loading" with the 8 ohm tap with your speakers.
Light loading is supposed to make the amp more linear, with significantly less distortion, and more headroom. Yes, there will be less power (negligible in my case), but the damping factor doubles. My speakers are rated between 8 and 12 ohms, so while I've used the 8 ohm taps on the amp, I'm not sure I'm getting the same benefit of light loading as others who might be using the 4 ohm tap for their 8 ohm speakers. Perhaps using the 4 ohm taps would be better. I'll go over to Audio Circle and post the question over there.
I've light loaded the RM10s and RM9s and prefer the 8 ohm tpa with the Merlins - in part, this must be because the VSMs are not speakers seaking more damping from the amp, so it might be very speaker dependent. There is a thread on Audio Circle like you mention. Might be an interesting question as a separate thread, that is the whole light loading approach with amps that have differrent rated taps.
Just looked at the Merlin VMS impedance graph (Stereophile), at it shows it only drops (over a very narrow band)to a minimum of 6 ohms at around 170hz at 0 phase angle.
This is an easy to drive speaker and should be driven off the 8ohm tap. Buy driving of the 4ohm tap all you achieve is loss of power from the amp, vitually no gains whatsoever.

Cheers George