Lightspeed Attenuator - Best Preamp Ever?


The question is a bit rhetorical. No preamp is the best ever, and much depends on system context. I am starting this thread beacuase there is a lot of info on this preamp in a Music First Audio Passive...thread, an Slagle AVC Modules...thread and wanted to be sure that information on this amazing product did not get lost in those threads.

I suspect that many folks may give this preamp a try at $450, direct from Australia, so I thought it would be good for current owners and future owners to have a place to describe their experience with this preamp.

It is a passive preamp that uses light LEDs, rather than mechanical contacts, to alter resistance and thereby attenuation of the source signal. It has been extremely hot in the DIY community, since the maker of this preamp provided gernerously provided information on how to make one. The trick is that while there are few parts, getting it done right, the matching of the parts is time consuming and tricky, and to boot, most of use would solder our fingers together if we tried. At $450, don't bother. It is cased in a small chassis that is fully shielded alloy, it gets it's RF sink earth via the interconnects. Vibration doesn't come into it as there is nothing to get vibrated as it's passive, even the active led's are immune as they are gas element, no filaments. The feet I attach are soft silicon/sorbethane compound anyway just in case.

This is not audio jewelry with bling, but solidly made and there is little room (if any) for audionervosa or tweaking.

So is this the best preamp ever? It might be if you have a single source (though you could use a switch box), your source is 2v or higher, your IC from pre-amp to amp is less than 2m to keep capaitance low, your amp is 5kohm input or higher (most any tube amp), and your amp is relatively sensitive (1v input sensitivity or lower v would be just right). In other words, within a passive friendly system (you do have to give this some thought), this is the finest passive preamp I have ever heard, and I have has many ranging form resistor-based to TVCs and AVCs.

In my system, with my equipment, I think it is the best I have heard passive or active, but I lean towards prefering preamp neutrality and transparency, without loosing musicality, dynamics, or the handling of low bass and highs.

If you own one, what are your impressions versus anything you have heard?

Is it the best ever? I suspect for some it may be, and to say that for a $450 product makes it stupidgood.
pubul57
09-22-11: Clio09
In my conversations with some designers the indication was that active preamps are responsible for a larger source of the noise in ones system than amps (assumption is we are talking similar designed equipment).... Adding any passive preamp I own (a TVC and the LSA) to the chain and then shorting the inputs on the preamp the noise level does not change (regardless of volume level). I can't say that for active tubed preamps (mine and other's systems), especially those that use tubes.
Interesting, Anthony. I would add the thought, though, that the increase in noise that occurs with an active preamp could often be due in part to ground loop effects occurring between the active preamp and the amp, especially if the interface is unbalanced. To the extent that may be the case, a dilemma would arise, both philosophically and technically, as to which component is really responsible.

Paul, thanks for your comment.

Best regards,
-- Al
Al - agree with your point on ground loops, especially if the resulting noise is 60Hz hum. That is why if I suspect a ground loop I use the Jensen plugs to determine the component that is responsible. As I suspect you know, as you are familiar with Jensen products, this would be a good test method.
Agreed, Anthony. That certainly reinforces the meaningfulness of the experiments you cited.

This Jensen paper may be of interest to others who are following this thread. It explains why unbalanced interfaces between components can be prone to both low frequency hum and high frequency buzz, resulting from ground loop effects.

Best regards,
-- Al
That is an interesting experiment Tony. I wonder what the technical explanation would be for that finding? It does not make sense.

Can anyone else describe their experiences with the LSA and SS amplification? I am still wondering the flat sound staging and what that is a byproduct of?
What doesn't make sense Andrew?

Seems like it made sense to Al who replied that my methods reinforced the meaningfulness of my tests. I as well as many others around here respect his opinion.

Have you tried these tests yourself?

I sense you're about to start helping your "friends" again;)