Lightspeed Attenuator - Best Preamp Ever?


The question is a bit rhetorical. No preamp is the best ever, and much depends on system context. I am starting this thread beacuase there is a lot of info on this preamp in a Music First Audio Passive...thread, an Slagle AVC Modules...thread and wanted to be sure that information on this amazing product did not get lost in those threads.

I suspect that many folks may give this preamp a try at $450, direct from Australia, so I thought it would be good for current owners and future owners to have a place to describe their experience with this preamp.

It is a passive preamp that uses light LEDs, rather than mechanical contacts, to alter resistance and thereby attenuation of the source signal. It has been extremely hot in the DIY community, since the maker of this preamp provided gernerously provided information on how to make one. The trick is that while there are few parts, getting it done right, the matching of the parts is time consuming and tricky, and to boot, most of use would solder our fingers together if we tried. At $450, don't bother. It is cased in a small chassis that is fully shielded alloy, it gets it's RF sink earth via the interconnects. Vibration doesn't come into it as there is nothing to get vibrated as it's passive, even the active led's are immune as they are gas element, no filaments. The feet I attach are soft silicon/sorbethane compound anyway just in case.

This is not audio jewelry with bling, but solidly made and there is little room (if any) for audionervosa or tweaking.

So is this the best preamp ever? It might be if you have a single source (though you could use a switch box), your source is 2v or higher, your IC from pre-amp to amp is less than 2m to keep capaitance low, your amp is 5kohm input or higher (most any tube amp), and your amp is relatively sensitive (1v input sensitivity or lower v would be just right). In other words, within a passive friendly system (you do have to give this some thought), this is the finest passive preamp I have ever heard, and I have has many ranging form resistor-based to TVCs and AVCs.

In my system, with my equipment, I think it is the best I have heard passive or active, but I lean towards prefering preamp neutrality and transparency, without loosing musicality, dynamics, or the handling of low bass and highs.

If you own one, what are your impressions versus anything you have heard?

Is it the best ever? I suspect for some it may be, and to say that for a $450 product makes it stupidgood.
pubul57
Clio09: what's a jensen plug? I looked up Jensen 'iso-max' products but there is a legion of them. Which one are you referring to? Is it for diagnosis or treatment?

Regarding lifting the ground, the only other item I have with a 3 prong plug is my stage. I use the walwart that George pointed to and it is two pronged. My tt's power supply is also 2 pronged. I tried a cheater plug with the stage and it didn't help. I had entertained the thought that it was the LSA's walwart that might be responsible. But I swapped in a battery supply I have and the same noise persists.

I once considered a switcher but I'm over it as well. I use almost exclusively my tt, and swapping IC's is easy because I have an open rack. I can see the appeal though if one had a cabinet and switched sources constantly.

I'd be interested in hearing the difference a switcher makes though. Anyone use one?
There should be only one mains earth point in a system, (if you have more than one you will have a loop), all the other components will get their earth via the interconnects from the one that is earthed. Once you have two components earthed then it will become a loop via the house earth line.
Even when I had two monoblock 805 tube SE that I built, I got a virtually no hum when only one was earthed and the other got it's earth via the interconnect to the Lightspeed and back down the other interconnect to the unearth monoblock.
PS wonder if I'll get the magic 1,000 post with this as they moderate my posts for up to 6 hours before approval.

Cheers George
Here is what you are looking for:

http://www.jensen-transformers.com/isokit1.html

In the photo you will see two plugs in the lower left with orange barrels. These can be purchased separately and IIRC are less the $20. They are diagnostic only, but more accurate than shorting plugs at isolating ground loops.

Only other reason I can think of for the noise is RFI. Phono stages and tubed ones especially are notorious for picking it up, cables too.
Well this thread has resulted in 1000 posts, quite an amazing feat. Thanks to Pubul57 for starting it. Lightspeed ahead to the next 1000 posts.