Lightspeed Attenuator - Best Preamp Ever?


The question is a bit rhetorical. No preamp is the best ever, and much depends on system context. I am starting this thread beacuase there is a lot of info on this preamp in a Music First Audio Passive...thread, an Slagle AVC Modules...thread and wanted to be sure that information on this amazing product did not get lost in those threads.

I suspect that many folks may give this preamp a try at $450, direct from Australia, so I thought it would be good for current owners and future owners to have a place to describe their experience with this preamp.

It is a passive preamp that uses light LEDs, rather than mechanical contacts, to alter resistance and thereby attenuation of the source signal. It has been extremely hot in the DIY community, since the maker of this preamp provided gernerously provided information on how to make one. The trick is that while there are few parts, getting it done right, the matching of the parts is time consuming and tricky, and to boot, most of use would solder our fingers together if we tried. At $450, don't bother. It is cased in a small chassis that is fully shielded alloy, it gets it's RF sink earth via the interconnects. Vibration doesn't come into it as there is nothing to get vibrated as it's passive, even the active led's are immune as they are gas element, no filaments. The feet I attach are soft silicon/sorbethane compound anyway just in case.

This is not audio jewelry with bling, but solidly made and there is little room (if any) for audionervosa or tweaking.

So is this the best preamp ever? It might be if you have a single source (though you could use a switch box), your source is 2v or higher, your IC from pre-amp to amp is less than 2m to keep capaitance low, your amp is 5kohm input or higher (most any tube amp), and your amp is relatively sensitive (1v input sensitivity or lower v would be just right). In other words, within a passive friendly system (you do have to give this some thought), this is the finest passive preamp I have ever heard, and I have has many ranging form resistor-based to TVCs and AVCs.

In my system, with my equipment, I think it is the best I have heard passive or active, but I lean towards prefering preamp neutrality and transparency, without loosing musicality, dynamics, or the handling of low bass and highs.

If you own one, what are your impressions versus anything you have heard?

Is it the best ever? I suspect for some it may be, and to say that for a $450 product makes it stupidgood.
pubul57
Last question. What temp fluctuations are you assuming in these cases? How hot? Over 90 degrees F? Thanks...
It's more that if you calibrate for ambient ie: 15c to 35c that's ok, but when the tubes and their transformers can add another 40c or so to that ambient inside the chassis, the ldr's will need to be recalibrated to that temp.
Where in the production stand alone Lightspeed Attenuator there is nothing inside the case to add to whatever the ambient is, so it stays in calibration, unless someone sits it on top of say a Pass Labs XA***.5 class A amp,then your asking for trouble and the same will happen to it.

Cheers George
When I take temps in my preamp (tube) I have never read temps any higher than 90 - 102 degrees F. If the room temp is 75 degrees, then I assume no issue?

For cost and hassle reasons the thought of an LDR is very interesting. Shallco attenuators are very expensive and a lot of work. They sound fantastic and I must admit doubt that a low cost LDR would sound as good.

But, I have never directly compared in an active preamp and am open to trying. If it sounded as good, then it would be a nice alternative for sure.

Not sure if anyone has done this type of comparison in an active preamp. Hard to do without having two of the same preamp for comparison. I suppose one could solder in and out the two attenuators, but going back and forth would be a HUGE hassle.
I believe Audiogon member Dgarretson put an LDR volume control in his Atma-Sphere preamp. In fact he may have mentioned it in this thread somewhere. You might try pinging him.