2. amps-preamps
  3. 1226436662

Ground Loop Issue 427

After talking with the manufacturer's of both the amps & preamp, I still have a 60hz hum. Here's the story:

Just changed amps to 845 SET monos, and now I hear the hum whenever the amps are on and RCA interconnects are connected to the amp inputs. Didn't have the problem with two prior pairs of amps. The pre could be turned off, and I still hear the hum. With shorting plugs in the amps, no hum.

The pre is battery powered, with no ac cable, and the trouble persists whether or not any sources are connected to the pre.

I've tried multiple types of interconnect, including the heavily-sheilded cheapos from a vcr, but no change.

One friend questions if adding a "hum potentiometer" to the amps would make sense. Others have suggested the $600 Granite Ground Zero, which is unaffordable for me.

I've already tried cheater plugs any/everywhere. I've added a grounding wire between the monoblocks metal bottom plate and floating one power cable while leaving the other grounded, all per the amp manuf's suggestion. I've tried HighWire LiveWires, which might be good sonically for RFI, but aren't helping the hum issue. This is a music only rig, no cable tv anywhere in the room. I am in a heavy RFI area, 1000ft from a radio tower, if that matters...

Anybody got any suggestions other than moving elsewhere? Thanks,

Spencer
128x128sbank
amandarae
512 posts
 
Hello Jim,

I understand what you meant and I am having a hard time to explain it and maybe I am getting confuse as well but I was talking about signal ground not PSU ground.

Don't know how to elaborate it any further really since it is easier for me to see it if I feed section by section from a freq generator, the way my mentor taught me, and look at the output to determine the loop. This simply means that the signal groundpath has to travel one direction: input-----> output and if it is not the case, a scope will display noisy output from the stage under test which verifies the ground loop that can manifest itself as a loud hum.

Apologies Jim, I am out of words to explain what I really wanted to.

regards,

Abe
atmasphere's avatar
atmasphere
11,784 posts
 
Hi Spencer, I'm in the camp of 'you have an RF problem'. I think, based on reading all of the above, that you have more RF susceptibility with with this amp, and that the long cables are somehow able to contribute where the other amps were not so susceptible. I don't think its a sensitivity issue.

There could also be a preamp issue that has not manifested before. If you can get your hands on a DVM, check and see if there is any continuity (less than 1 ohm) between the connectors and the chassis. Sometimes if the chassis is only grounded through the wall and the circuit isn't grounded to it you can run into trouble. That's not so bad in an amplifier but in a preamp it can result in hum, even if it worked fine with other amps!

Back to the RF issue: Have you tried different cables?
sbank's avatar
sbank OP
3,378 posts
 
Hi Ralph,

Thanks for your interest.

I did move the preamp over near the amps, and tried multiple different 1m cables, including the highly shielded cheapo ones from a vcr(ie with the red/white/yellow all bundled together), and the hum persists, even when the preamp's power is off.

My DVM doesn't read continuity, but I'll try to borrow one that does.

So do you think that if it's RFI, that the Jensen Isomax transformer would help or not?
jea48
4,416 posts
 
11-17-08: Atmasphere
There could also be a preamp issue that has not manifested before. If you can get your hands on a DVM, check and see if there is any continuity (less than 1 ohm) between the connectors and the chassis.

" Sometimes if the chassis is only grounded through the wall and the circuit isn't grounded to it you can run into trouble. That's not so bad in an amplifier but in a preamp it can result in hum, even if it worked fine with other amps!"


11-13-08: Sbank
Abe, according to the preamp designer, "All of the rca's on the preamp are isolated from the chassis and connected vis the 8 ga. buss. The chassis is grounded thru the charger jack only."

Atmasphere,
Is it possible the preamp is acting like a big antenna?

I still think Amandarae is on to something about the SET inputs being more sensitive than the other Amps Sbank was using.

Sbank, did you ever connect a wire from the chassis of the preamp to one of the amps chassis?

http://www.audioasylum.com/audio/general/messages/52/525608.html
sbank's avatar
sbank OP
3,378 posts
 
Jim,

Until my new tri-wire speaker cables arrive in a week or so, I can't try anything(the old speakers were sold this week), but I will try running a grounding wire from preamp to power amp chassis.

I did already run a grounding wire from one amp chassis to the other amp chassis, per suggestion from the amp designer.

I'll post again after trying that(as well another preamp), and we'll see what progress is made. Thanks,
Spencer
More to discover