2. amps-preamps
  3. 1254429799

Preamp w/ xlrs in the ht-bypass loop

Hello, I'm looking for a two channel preamplifier with a pair of balanced inputs that are included in the home theater bypass loop. I've done a little bit of research and there isn't that many that do this or they're a little over my budget. Mark Levinson has a few but I'd be looking at about $4000 used which is a little more than I was looking to spend and I'd rather buy new anyway. The one that would fit the bill perfectly is the Ayre K-5xe. However, I read the manual and I would need to pull the plug every time to engage the bypass. And the way my rack is set up, that's apples to apples as it would be the same, if I went back there to switch the cables myself. Anyway, if some of you guys could lists some models to check out, I'd appreciate it. The features that I need are simple, with the first three being mandatory, and I'll list them below.

1) Two balanced inputs included in the ht bypass loop- as mentioned above.

2) Has to be fully balanced- I'm not looking to sacrifice anything for the convenience of home theater bypass.

3) Has to be SS- I'm not running tube gear and I do not want to mix and match. I realize this limits the field.

4) I'd like to spend $3000, hopefully less- I'd like to buy new but I'm open to used

5) Less is more- I'm only running a CD player and the amplifiers for my fronts. So that's one pair of balanced outputs and two pairs of balanced inputs. I'll take another set of balanced inputs for a computer DAC, down the road, but it's not a priority. Staying with "less is more," I'd really prefer it to be completely analog. I'm trying to avoid anything that may introduce noise; even those big florescent displays are a concern.

6) Remote- a remote would be nice but not a must

I'm willing to audition anything that includes the first three features on this list; the rest is a bonus. I appreciate the help.
bostongeorge34
bostongeorge34 OP
7 posts
 
Hello Larryski2, if you're able to bypass the preamp without needing to disconnect and then reconnect the power, that's great news. When you're using the Integra 9.8, do you see the letters "PP," for processor pass-through, on the Ayre?

I think I may have read the manual wrong. It looks like you only need to do this once to program the unit. This is from page 12 of the manual on Ayre's website.

To activate the “Processor Pass-Through” mode for
that input, remove the AC power from the K-5xeMP
for at least 10 seconds. Then, while pressing the
input selector button corresponding to the chosen
surround-sound processor input, re-connect the AC
power.
The chosen input is now programmed for “Processor
Pass-Through” operation, disabling the now
redundant volume control of the K-5xeMP. When
that input is selected, the preamplifier section of the
K-5xeMP is set to unity gain (0 dB), and the volume
is controlled directly from the surround-sound
processor. The volume indicator of the K-5xeMP will
display “PP” to show that the “Processor
Pass-Through” mode has been selected for that
input.
To clear the “Processor Pass-Through” mode from
an input and restore normal operation, remove the
AC power from the K-5xeMP for at least 10 seconds.
Then, while pressing the “Mute” button, re-connect
the AC power.

Is that what you needed to do to assign an input? Did you do anything else differently? Thanks
bostongeorge34 OP
7 posts
 
Thanks Somec59, I'll make sure to look at PS Audio too.
hevac1
812 posts
 
My ARC Ref3 has balanced HT passthrough. It is unity gain but I think it sounds better going thruogh the Ref3 than a direct connection from my Meridian G68AXV.
larryski2
37 posts
 
Bostongeorge34.....

In answer to your question:

if you're able to bypass the preamp without needing to disconnect and then reconnect the power, that's great news. When you're using the Integra 9.8, do you see the letters "PP," for processor pass-through, on the Ayre?

Yes. With the power on, and when using the pass through input (which is assignable to any of the four inputs as you have described) you do see the PP on the Ayre.

My understanding is that the unit was designed to be left in the on position all the time. The only draw back that I encountered with this is that my amp does not have a power on/power off remote setting, and the Ayre has no trigger output.

To overcome this without leaving the amp "on" 24/7 I have to turn on the Integra to utilize it's trigger, to turn on the amp (which I can do with my remote). I then have the Integra set to an open/unutilized input, so there aren't duplicated sound signals being transmitted. It was a minor workout, and I love the Ayre.

Good luck with whatever you decide on.
stringreen's avatar
stringreen
6,474 posts
 
..that doesn't sound right BostonGeorge34... I have an Ayre K1xe that has a balanced monitor loop that you don't have to pull the plug to reset. I would call Ayre...they are very nice and will provide the right answer for you.
More to discover