2. amps-preamps
  3. 1367679356

DIY question on a preamp problem could use help...

Ok, love to hear from some of you who have good technical skill to help diagnose a problem. I purchased a used Lector Zoe preamp as an upgrade project. The unit has a lot of tube hiss/rush sort of noise through both speakers. The builder is no help as I have emailed them several times and they keep telling me to use a different tube. I have tried several tubes brand new and nos , but the same tube noise all the time. The preamp is very high gain as an FYI.

I am using two 6922 tubes. I have already modified the unit to sound far better with great results. None of the mods helped with the tube hiss that was present before and after my mods. I upgraded many caps and put in a nice Goldpoint stepped Attenuator with DACT remote. Lastly I bypassed the selector switch and went direct from the RCA input to the Goldpoint as I only use one source. I upgraded the signal wire and the end result is quite stellar. Problem is this tube hiss/rush noise that is constant through both speakers. I want to fix this and greatly reduce the noise. Where do I look?

Would reducing the gain help? Should I look at the resistors on the 6922 tubes? Change the value of any of these resistors to reduce gain? Not sure where to go next? The noise is not really impacted that much at all as I turn the volume up. The tube hiss stays pretty constant regardless of volume. The signal goes from the coupling caps right to the RCA outputs with no resistors after the coupling caps or on the RCA outputs to ground.

Any ideas?
128x128grannyring
grannyring's avatar
grannyring OP
6,530 posts
 
The tubes came from Upscale Audio and they do a great job testing. Great points all, but I have been there and done that. I use unshielded ic's by Anti Cables, but also tried the well shielded IC from Blue Jean cables and the same hiss was present.

I have done all the needed testing on sources, amps to be sure it is the pre and not the source or IC or anything else. It is the preamp.

As I mentioned above, the hiss does not change with volume and is always present even at very, very volumes.

The parts all test fine in the preamp. I know it is a circuit design thing and I will need to mod. Hoping someone would have an idea of where to try a mod.

I will continue to read all I can on this issue as I like the challenge! Love learning and trying .
grannyring's avatar
grannyring OP
6,530 posts
 
Mechans, you are right about NOS's and perhaps Upscale's tubes are still noisy? I am going to try another set which the builder says are the quietest in the preamp. ECC802s from JJ.

We will see.
zd542
5,339 posts
 
There should be no problem confirming that the problem lies in the preamp by removing it from the system and just using the volume control on the dac. Other than that, I think the OP is right in that the preamp is the issue. After reading Onemugs post and finding that the only IC's used were Blue Jeans and Anti Cables, I feel there is a small chance the problem may be the IC's. I've has several situations where noise was due to IC's picking up noise.

Another resource you may want to try is The Cable Company. A lot of people think of them for only cables, but they sell a lot of tubes. I don't want to start a war, but I feel Upscale is very overrated. Cable Co. and maybe one or two other dealers, I feel is the most reputable I know of. They'll send you some tubes to try first so you don't have to buy anything. Also, as I mentioned above, I think there is a small chance the IC's may be at fault. I find AQ cables to be extremely well shielded. If you can try a pair of those, it wouldn't hurt.

I just thought of one last thing. Are you sure its not a ground issue?
grannyring's avatar
grannyring OP
6,530 posts
 
I did and do go direct from my dac to amps with dead silence both with the unshielded and shielded cables. Sound it fantastic direct also. I just love modifying gear to be the best it can be....thus this preamp project.

I will try another set of ic's and tubes.
clio09
3,360 posts
 
From my own personal experience I think Upscale's testing is a bit spotty. I have bought two separate sets of "low noise" tubes from them with the purchases several years apart. Both sets were noisy.

Try to contact Roger Modjeski. He has done preamp and phono stage designs using the 6DJ8/6922 and his designs are notoriously quiet. Getting a set from him would enable you to do a valid test as to whether the tubes are indeed the problem.
More to discover