Classe CA-100 stereo vs bridged

Yes, the 600w 4 ohm mono rating is a bit suspect, but irrelevant in my case since my impedance low is about 6 ohms.

Thanks for the replies.

Id still like to hear from others as well if anyone has some input.

That 600W 4 ohm mono rating has to be peak power. What sane person needs 600W continuous in a home environment anyway? I've known of a few people who have run bridged pairs of various Classé amps, and had no complaints about performance. The company has not been known for inflating power ratings. In reviews their products have always met or surpassed published output specifications on the test bench. If they say their amp does 4 ohms bridged, I trust them.

My guess is that the 350W/600W 8 ohm/4 ohm mono ratings, which are shown in the manual and in the fancily printed part of the brochure, are accurate.

The white spec sheet showing 200W/400W, that is part of the brochure pdf, I suspect is a document that is earlier and preliminary. I say that based in part on its look, compared to the other documents. But note also that it specifies S/N ratio as "more than 100 db," as if someone made up the spec before they had more precise knowledge of it, while the other documents specifically indicate 128 db (although the reference level isn't specified).

Also, peak vs. RMS would not account numerically for the disparity between the two sets of numbers. Unless perhaps "peak power" is interpreted to mean "dynamic (short term) RMS power," or more precisely "dynamic (short term) average power." But that would make the numbers that are presented for stereo and mono modes completely inconsistent with each other, and be very misleading. I very much doubt that Classe would specify things in that manner.

Keep in mind, also, that potentially/ideally a bridged amp can output four times as much power as when the same amp is operated in stereo mode, since the output voltage swing capability is doubled. Although in practice the 4x factor usually comes out to be significantly less, due to current and/or thermal limitations.

In any event, given the impedance characteristics of your speakers you should be fine either way.

Regarding question 2, I wouldn't be surprised if the sensitivity increases by 6 db (i.e., you would have to reduce your volume control setting by 6 db, to achieve the same volume as in stereo configuration). But without being familiar with the details of the design, I don't think we can be certain of that.

Regarding question 1, I wouldn't want to venture a guess as to how the sonic differences would net out, without having tried it on the same or similar models, and with a speaker having similar impedance characteristics.

Regards,
-- Al

Okay, I'm confused(nothing unusual). What does having to reduce my volume control have anything to do with sensitivity when the amp is now producing, real world, probably three times as much power at the same setting? Won't an amp making three times as much power produce at least 4-5 db more spl at the same volume setting with the 'same' sensitivity? I ask because I'm running my Acoustats in mono and am curious as to why exactly I have to turn up my self powered sub woofers substantially to eq the system as opposed to using them in stereo.

Thank you, Al

BTW, No degradation. Rather, an improvement. 2nd order harmonics are eliminated, way more dynamic, faster.

Hi Peter (Csontos),

First, let me repeat what I said:

I wouldn't be surprised if the sensitivity increases by 6 db (i.e., you would have to reduce your volume control setting by 6 db, to achieve the SAME VOLUME [emphasis added] as in stereo configuration)

You then asked, in part:

Won't an amp making three times as much power produce at least 4-5 db more spl at the same volume setting ....

Our two statements seem to me to be perfectly consistent with each other.

The rest of your sentence was:

... with the 'same' sensitivity?

If sensitivity is considered to be the input voltage required to drive the amp to its maximum power rating, whatever that rating may be for the specific mode that is being used (stereo or bridged mono), then the amp's sensitivity would probably be the same.

But my interpretation of the intent of the OP's question about whether input sensitivity would change is that he wanted to determine if there would be a significant change in output power for a GIVEN input voltage.

You have found that to be the case with your Acoustat amps, and I was saying that I wouldn't be surprised if it were the case with his Classe amp.

Whether or not that increase in output power and volume for the same setting of the volume control is considered to be a change in "sensitivity" is a matter of semantics and definition. I chose not to get into semantics and definition, but to respond to what I perceived to be the intent of the question.

Best regards,
-- Al