Anyone try this way to wire your loudspeakers?

Not to take away anything from the enjoyment you're experiencing . . . but I thought I'd point out that the 8-ohm taps have about 6dB more voltage gain than the 4-ohm taps. There's no problem with doing this from the amplifier's standpoint, except with the possibility of somewhat increased distortion should the loudspeakers' high-frequency section present significantly less than an 8-ohm load through part of the frequency range.

But the sonic effects are overwhelmingly akin to simply cranking up the bass relative to the highs - very simply a tone control, that has frequency characteristics of the loudspeakers' crossover slope(s). The configuration of the cables themselves are unlikely to have anything except a miniscule effect when compared to this change in gain.

Again . . . if you like what you hear, that's great! For those that don't have multiple amplifier taps or loudspeaker bi-wire inputs, a very similar result could be had with a simple twist of a well-designed tone control.

Kirk, you beat me to it! And it's nice to see you posting again.

A minor point, though. Wouldn't the 8 ohm tap have 3 db more voltage gain than the 4 ohm tap, not 6 db? In other words a factor of 1.414, resulting in the output transistors seeing the same load when an 8 ohm load is connected to the 8 ohm tap, as when a 4 ohm load is connected to the 4 ohm tap, as when a 2 ohm load is connected to the 2 ohm tap (since the impedance transformation will be proportional to the square of the turns ratio, and hence to the square of the voltage ratio).

Beyond that, I second Kirk's statement that "if you like what you hear, that's great." And a good takeaway from the experience reported by the OP is that experimentation with how multiple output taps are utilized can pay off big-time.

A not so good takeaway, on the other hand, would be an expectation that a similar connection arrangement will necessarily, or even probably, be optimal in the case of other amplifiers and speakers (although it certainly MIGHT be). In contrast to most amps that provide multiple output taps (i.e., tube amps), the autoformer-based McIntosh designs have output impedances that are low enough to be essentially negligible, as they are with most solid state amplifiers. And the XR100 speakers are complex four-way affairs having 15 drivers per speaker, and who knows what kind of impedance vs. frequency characteristics (I couldn't find impedance curves for them). So the OP's system is considerably different in relevant respects than the majority of others.

To the OP, again, congratulations on some imaginative experimentation that has paid off. Enjoy.

Regards,
-- Al

Hi Al . . . good to be back as well. You are indeed correct, my bad. It's 6dB between the 8- and 2-ohm taps, and 3dB between the 8- and 4-ohm taps . . . same as a tube amp.

Al, I'm almost afraid to ask this Q, but here goes. Would it be a good, bad or neutral thing to use the 8 ohm tap for one speaker lead and the 4 ohm tap for the other lead?

Regards,

Bruce

Mchd1,

"I have a pair of Mirage M3si speakers and I do not intend to upgrade."

Those are really good speakers. I used to be a dealer and know them very well. They are much improved over the original M series. The si's have an excellent balance from top to bottom. The originals were laid back to a fault. No question the best speakers Mirage has ever made.

Bojack,

05-31-13: Bojack
"Good speakers use good wires."

Tell that to Spencer and Derek Hughes and legions of other speaker designers who have designed the world's finest speakers! The key to great sound is called "design," not "cable."

How on earth do you get all that from 1 line? To be honest, though, I would definitely tell them that. Why wouldn't good designers use good parts to design their speakers? I don't really keep track of such things but I can tell you that I do know of some speaker manufacturers who use brands like Cardas and Audioquest for the internal wiring of their speakers, and other components as well. It wouldn't suprise me if they all do, but like I said, I really don't keep track.