Since my last post, I was lucky enough to speak with Bill Whitlock of Jensen, who is both very knowledgeable and willing to give thoughts and suggestions about my situation. He observed that the gain mismatch I am getting would be best remedied by somehow getting more output from the KUBE. I sent him schematics of the KUBE and he replied back very quickly, instructing to change out 2 resistors in the variable output circuit for lower values, which would extend the gain by a few dB. He said that I could stick with the RCA to XLR cables the way I had them wired, but suggested that if I got any noise, I should try combining the shield with the black conductor at the RCA end. If no luck there, then I should look into getting a PI-2RX, etc.
I have yet to do this because I haven't gotten the parts, but in the meantime, I figured I'd had a go with db's suggestion above and just try it for myself. I hooked it up, non-biamped, and gave it a go.
I have to say I really don't notice any discernible difference in the HF with the KUBE inline. It may be that my gear is just not good enough to expose anything, but I went back and forth a few times and I'll be damned if I heard any detrimental effects on the mids or highs.
The first difference I did notice is, I have less gain from using the RCA to XLR outputs from the KUBE to my amp. I have to crank the preamp up a bit more, but I thankfully don't have any hiss, buzz or hum. I'm going to live with this setup until I get the parts I need to mod the KUBE for biamping, or I may just make another set of RCA to XLR cables and forget the balanced preamp output altogether.
Now, as far as using the KUBE...and forgive me if I am taking this thread off into the weeds... The whole point of getting one (for me) was to see just how well it could extend the low end. As db pointed out, the KUBE is not "required" for the 105/3, but it's an option if you feel you're missing out on the lower octaves. I can say that it does indeed work as advertised, but I think it may be at the expense of overall SPL and some very obvious strain on the woofers.
A few observations:
- With the LF and HF controls set at the center notch (which I would think would be flat), there was a noticeable bass boost when bypassing and un-bypassing the KUBE, so it seems those knob positions are not flat, or the same as bypass.
- When engaging the KUBE at a decent volume with the LF contour slightly increased and some moderately bass-heavy material, the bottom woofer's movement started to scare me...
- The KUBE seems to not only extend the bass, but also change the tone of the bass, if that makes any sense. I noticed this regardless of whether the LF knob was centered or not. It almost seems like I lose a tiny bit of upper mid-bass as soon as the KUBE is un-bypassed.
Overall, I think the KUBE on the 105/3 is a nice option if you want to get a little more oomph, but only at low to moderate volumes. For "critical" listening or filling the house with music, I would be wary of using it for fear of damage. IMO, the KUBE tries to make the 105/3 woofers do something for which they were not designed.
I have yet to do this because I haven't gotten the parts, but in the meantime, I figured I'd had a go with db's suggestion above and just try it for myself. I hooked it up, non-biamped, and gave it a go.
I have to say I really don't notice any discernible difference in the HF with the KUBE inline. It may be that my gear is just not good enough to expose anything, but I went back and forth a few times and I'll be damned if I heard any detrimental effects on the mids or highs.
The first difference I did notice is, I have less gain from using the RCA to XLR outputs from the KUBE to my amp. I have to crank the preamp up a bit more, but I thankfully don't have any hiss, buzz or hum. I'm going to live with this setup until I get the parts I need to mod the KUBE for biamping, or I may just make another set of RCA to XLR cables and forget the balanced preamp output altogether.
Now, as far as using the KUBE...and forgive me if I am taking this thread off into the weeds... The whole point of getting one (for me) was to see just how well it could extend the low end. As db pointed out, the KUBE is not "required" for the 105/3, but it's an option if you feel you're missing out on the lower octaves. I can say that it does indeed work as advertised, but I think it may be at the expense of overall SPL and some very obvious strain on the woofers.
A few observations:
- With the LF and HF controls set at the center notch (which I would think would be flat), there was a noticeable bass boost when bypassing and un-bypassing the KUBE, so it seems those knob positions are not flat, or the same as bypass.
- When engaging the KUBE at a decent volume with the LF contour slightly increased and some moderately bass-heavy material, the bottom woofer's movement started to scare me...
- The KUBE seems to not only extend the bass, but also change the tone of the bass, if that makes any sense. I noticed this regardless of whether the LF knob was centered or not. It almost seems like I lose a tiny bit of upper mid-bass as soon as the KUBE is un-bypassed.
Overall, I think the KUBE on the 105/3 is a nice option if you want to get a little more oomph, but only at low to moderate volumes. For "critical" listening or filling the house with music, I would be wary of using it for fear of damage. IMO, the KUBE tries to make the 105/3 woofers do something for which they were not designed.