Analog output for hifi
The composite audio/video on the TV is likely an input and not an output. Here is how I connect my TV to a 2-channel system, and it works extremely well. Digital output on the TV to this inexpensive DAC, https://www.bhphotovideo.com/bnh/controller/home?O=&sku=890577&gclid=COPFr8nf5NACFVU7gQodBk0... then analog L&R from it to the system. The digital output on the TV will need to be set to PCM. You could always use a more expensive DAC, however, I was pleasantly surprised with the sound of this cheap DAC. It is considered the best of the many at that price. Take a look at how it is built. https://m.youtube.com/watch?v=XVgFIDiZSHk This will get things working well, and as I said, you can upgrade to a more expensive DAC later if you desire. |
kijanki, obviously my Sony has a selection for PCM. Also, I just looked at a few manuals online for other brands, Panasonic included, and all had a selection for PCM in the menu. I suppose it is possible to not have it, but IMHO, this is not typical. It is true that no TV comes set to PCM, and it must be selected. Don, I was using a 3.5mm to RCA prior to getting the cheap DAC listed in my previous post, however no hum problem. I got the cheap DAC to see how it worked, thinking I would possibly get a better one. It was an improvement over the 3.5mm hookup, and currently I happy to just use it. I think there is a good possibility that if you change your setup to optical and a DAC, the hum might be eliminated. At 20 bucks for the DAC plus optical cable, it's cheap enough to try. |
tls49, My daughter's Panasonic does not have menu selection. None of Panasonics in ABT Electronics store had it. Same for LG. We checked manuals with specialist in the back of the store. This problem with Panasonics was mentioned in many threads. Below link to manual of new 4K Panasonics TVs: ftp://ftp.panasonic.com/television/ehelp/tc-55cx800_en_ehelp.pdf On p.54 it states that: When ATSC channel is selected, the output from DIGITAL AUDIO OUT jack will be Dolby Digital. When NTSC channel is selected, the output will be PCM. |
kijanki, not so sure the specialist understood the manual. Look at p.160 in the manual under advanced settings. There is a selection between Auto and PCM. The PCM setting states, "Digital output signal is fixed to PCM". The statement on p.54 applies to what happens in the Auto setting. Please understand I'm not trying to start a disagreement. I just want to provide the most correct information. I will investigate further and also look at a new LG manual. Just so you know, I'm retired now but worked in A/V and high end audio for over 25 years, and have even kept myself informed of the latest since retiring. |
Not as simple as the Panasonic, but I have found how to set for PCM on the LG. In the user guide, go to 'Tour List of Settings', then Quick Settings > Sound > Sound Out > Audio Out(Optical/HDMI/ARC) > Digital Sound Out and select PCM. stanwal, you should be able to set your LG to PCM using the above procedure. kijanki, I think the problem is that due to the difficulty in finding how to set a TV for PCM output, many just give up, and assume it can't be done. Again, I'll say that it may be possible that a TV could not be set to PCM, however this is not typical. |
After reading that a DAC is the way to go, I bought a Schiit multibit bifrost for my Sony TV. Could not be more pleased after a 2 day break in. The opinions are correct, this is a great DAC. The DAC was $600 direct from Schiit. Set the Sony to PCM audio output, and the DAC feeds a Pass X1, Son of Ampzilla 2000, and Magnepan IIIa speakers in my high end home theater. Wish I used a DAC instead of headphone output sooner! |
