Cartridge Loading- Low output M/C

Dear @wynpalmer4: " I may not be a renowned Audio Designer..."""

Problem with we audiophiles is that almost all always think that reviewers and manufacturers are the ones that not only kno everything but that what they say always is " the Bible " and almost all of us are docile followers, pity for say the least.

The other problem is that we audiophiles think we understand " everything " in audio with out take in count that all of us are ignorant people in several audio subjects when in other audio subjects our ignorance levels are lower.
Additional to that when I speak of ignorance levels peoples feel that I’m trying to offend/hit them when it’s in not way. Ignorance is just that: ignorance.

Good that you came here to put a true " ligth " in that regards because the atmasphere seller is spreading that same capacitance issue all over the internet forums and like here @krelldog is " facinated " with 47koms @catcher10 just does not understand what you posted.

We all audiophiles in reality are not educated in what is wrong or good in what we are listening at our place/home and this ignorance level is the real brake that stops the high end faster developments. Go figure, we are in 2018 still using tubes in phono stages and the real problem is that audiophiles are jumping of hapiness with. To each his owns.

""" In most cases a resistance close to 100 ohms is fine- largely because the coil DC resistance is often a proxy for the inductance .... and as a result a 100 ohm load gives you a well damped electrical system..."""




Several years ago I remember a top LOMC cartridges evaluation made it in TAS where one of the reviewers was the TAS’s editor ( that pass away. ) where as was his " trend " always loaded his LOMC at 47kohm but he did it for way different reasons where one of them was that he was losting to fast his auditive sensitivity due that for many years he listened his audio system at way to high SPL ( he had the Infinity IRS loaned from years. ) and where that sensitivity affects more is at the high frequency range that’s what shows that wrong 47kohms loading. We " love " that " transparency/spark "/detail in that range with out take in count that only are higher distortion levels. You said it:

""" Unfortunately accentuated dynamics and resolution all too often mean a really nasty peak at the HF ....... ferences in response that occur due to changes in load are in the 10k-20kHz range. """

Well, audiophiles as me sometimes we don’t like 100ohms loads because in many audio systems makes that we " feel " that the sound is " dull " but the problem is not on the load it self but in the system/room interaction and that our MUSIC/sound priorities are wrong choosed and sometimes is because we not only don’t attend often to live events but there are people that not even does one time in a year ! ! and this is a serious trouble.



"""
I’m a believer in fixing the problem where it exists and not by adding an additional parameter to an already over-constrained problem. """


with different words I posted something like that.

"" you can’t even simulate or calculate it to find a decent answer as no MC cartridge maker that I am aware of provides even simple models for their device, even when asked. """

it’s out of our control.

I’m way ignorant in several audio subjects and I wish to have a tinny very tinny fraction of your level knowledge/skills and experiences.

For my part really appreciated your posts. A learning lessons for all we true audiophiles that are always willing to learn and trying to sell nothing.


Regards and enjoy the MUSIC NOT DISTORTIONS,
R.

Wynpalmer4 5-25-2018

The non-inverting amplifiers used in an RIAA stage never have a gain below unity unless an additional pole is added. It’s hard to see why adding a capacitance of significant value to the input of a phono stage helps when the self resonant frequency of most larger value caps is well below the RF region of interest. Indeed, if that is your concern, then adding several caps of scaled value 1-2 orders of magnitude apart, say 0.1uF//3300pF//100pF as the cartridge load would be the way to go, and who does that- except as an extra pole in a non-inverting RIAA stage.
I’m a believer in fixing the problem where it exists and not by adding an additional parameter to an already over-constrained problem.

Thank you for your responses. I must say, though, that despite being a highly experienced electrical engineer myself (in my case analog and digital circuit design for defense electronics), I don’t see the relevance of this statement.

What I, Atmasphere, and Jonathan Carr have said in regard to load capacitance, and which the Hagtech calculators you referred to will confirm, is that in the case of LOMC cartridges **minimizing** load capacitance will increase the frequency and reduce the amplitude of the resonant peak which occurs at RF frequencies as a consequence of the interaction of cartridge inductance and load capacitance. Both of which are desirable goals, although it presumably won’t matter much if at all in the case of **some** phono stages (such as my Herron and I would assume the phono stages that are built into Atmasphere’s preamps).

But in the case of phono stages whose design is such that RF energy received at their inputs may have audible consequences keeping that resonant peak as small as possible and at as high a frequency as possible will mean that less resistive loading will be necessary to tame that peak. Which in turn can often be beneficial sonically, as has often been attested to by many highly experienced and astute audiophiles. A notable example being Larryi, who posted earlier in this thread.

So I’m not understanding why your statement that I quoted refers to adding capacitance, rather than minimizing it, or what the relevance of that statement’s concluding sentence may be.

Regards,
-- Al

^ I agree.......I have followed pretty much everything JCarr has stated in other forums about loading and all I can attest is my listening experience is much better for it.
The part that I focus on is that your LOMC should not be tasked to work so hard that it stiffens compliance, I can't see any good from that.

Unless you like buying a new cart sooner, much sooner, than normal.

@catcher10:  " stiffens compliance "?, you or any one but the cartridge designer can change cartridge compliance, certainly load can't do it.

R.

Dear @almarg : My " worry " here is not whom is rigth but more if things are pratically to any one of us, if we can do a easy as to load impedance changes. Normally cable manufacturers does not gives cable capacitance. I put the KK example but if you go to Audience ( OP cables. ) you can find out nothing.

Many times you can't know the ps fixed capacitance and the ones that comes with capacitive loading switch this works only when using MM but not when LOMC.

Ok, what's the problem to tame the peak ( as you said. ) loading at 100 ohms?

In the times of that TAS LOMC cartridges evaluations the specific cartridge loading never was associated to capacitance .

The advise is almost useless because we don't have or can have control on it to make any kind of changes about.

The cable manufacturers does not give the capacitance value but the tonearm manufacturers neither with the tonearm internal wires.

I don't think that that kind of advice from your part is of any help but only making more " noise " in the audiophile minds.

I always read your posts because always have very good contributions but for me not this time .

Now, always is good to have contributions as the wyn one. Don't you think?
I'm not technical oriented at your level but I always try to make things in the best way and in an easy way because at the end what I and we want is to enjoy the MUSIC and always is system dependent.

R.