Shahinian Oblisk


I have just purchased a McIntosh Tube Amp 2102 and Tube PreAmp 2200. The amp gives a choice of connecting my Shahinian Oblisk speakers to different OHM speaker settings.
1. Can someone please explain how the OHM effects the speakers.
2. Should I choose a higher or lower OHM setting for the Shahinian speakers.

Thank you in advance for your assistance.
kgksecurity
Your question is a little unclear, but I'd guess the OHM setting you're referring to is on the amp. If so, determine from the manual or the website what the nominal impedence of your speaker (expressed in ohms) is, then use the speaker terminals from your amplifier with the same or a lower impedence value to hook up the speaker wires. In the case of the Shahinians, they have a nominal 6 ohm impedence, I'd suggest using the 4 ohm terminals.
Kgk, Rcprince is right on with the 4 ohm tap. The "OHM" is the resistance your speaker presents to your amp. By selecting the proper tap on the back of the Mcintosh, the amp will run in its most linear state. That's a good thing. If whatever speaker you use is between the 2,4 and 8 ohm taps, use the tap that is the lower of the two. Enjoy.
Rcprince,

Yes, you are correct. The McIntosh amp has a choice of ohms level for connecting the speakers. I will go with your suggestion and use the 4 ohm terminals.
Can you explain what effect the a 2, 4, or 8 impedence has on the speakers? Does it have any influence on the reproduction of sound from your speakers? This is new to me. My old amp, a Bedini MK100 did not give me this choice. So I am hoping you can explain this to a novice like me. Thanks in advance.
I'm no technical guy, but Onemug is right. A tube amp, other than an OTL (output transformerless) design, uses an output transformer to match its output with the impedence load your speaker presents. A solid state design generally does not use an output transformer and thus does not have different taps. The taps represent different points in the transformer windings (a transformer is wire wound around a core)that are optimal for the load in question. Outside of that I can't tell you too much, I'll leave it to a more technically inclined poster to correct me/elaborate for you.

By the way, I noted another post where you were asking about speakers to go with your new amp--don't be too anxious to change the Shahinians quite yet until you listen to them a while with the Mac, you might be able to resist the upgrade bug. The Shahinians are similar to my speaker system in terms of being closer to an omnidirectional speaker than the other, forward-firing designs you mentioned in your other post, and as such they present music in a significantly different manner than those other speakers. If you like and are accustomed to the Shahinian "sound", you might have trouble listening to more conventional designs. The other designs may do some things far better, such as pinpoint imaging and presentation of low level detail, but the overall listening experience might not be as pleasurable.
As others have said, you usually want to match the nominal impedence of the speakers to the output impedence tap of the amp, HOWEVER the real test is which output tap sounds best and it isn't always the "correct" one. Try both taps and see which one sounds better. You will not damage the amp or the speakers.
I agree with all of the above, including Newbee. That is, the "typical" installation will have the speakers connected to a tap that is equal to or lower than the nominal impedance of the speaker. That can vary though depending on how accurate the nominal impedance of the speaker was rated and / or the actual impedance taps of the transformer itself.

It is quite possible that a tap that is higher in ohmic value may sound better with a given speaker. In such a case, the only real potential drawback that i see is that distortion may be a tad higher, damping factor slightly reduced and / or tube life might be shortened slightly. That's because the slight impedance mismatch will end up pulling more current through the tube than if a lower impedance tap was selected. Even then, i don't see this as being a major concern so long as on isn't consistently wailing on the throttle of a tough to drive speaker. The bottom line is that one should experiment in such a situation, but be careful and use common sense. Sean
>
A very astute suggestion by Newbee. Try all of them and choose which voice you sounds best to you as none will cause any damage to your amplifier or your speakers.
Why not just give Richard Shahinian a shout. I'm sure he would be more than happy to speak with you and give you some insight how best to enjoy his product. Try him at 516-736-0036
I would like to thank all of you for your useful insight on this topic. It is because of people like you that makes this site a pleasure to visit. Happy New Years to all!!!
As a fellow Shahinian-McIntosh-owner, my experience is that the Obelisks sounds best with the 8-ohm-tap
Speaking of Obelisks...
While this doesn't have an exact bearring on the specific question, if you go over to audio asylum and do a search on these speakers, there's a discussion from a year or three ago re. the unique design approach Shahinian takes with them and his Diapasons.
If I understand correctly, the Obelisks purposely use the acoustics of the listener's room to enhance a life-like presentation of the music. Since the actuall room is therefor in a way part of the speaker, I wonder what the ideal listening space for them would be with that in mind.
More to discover