2. amps-preamps
  3. 1033262025

Sibilance how do I get rid of it?

Hello
I am currently experincing a problem with sibilance in my system,I must admit I know that unless I set up a overly dampened ( lack of Hi's ) set up, I'm almost always going to have some degree of siblance,I listen to mass produced commercial cd's so I know that this is atleast 40% of my problem , and my listening room 26'x14'x8' is relatively live,,lanolium floors..no dampening,,etc,,
But somewhere in the back of my mind I hear "you need to do careful system matching,
My system consisits of:
Cal Aria MkIII CDP
Conrad Johnson Pv10a Pre
& Conrad Johnson PV 14L Pre
Llano A100 SS Amplifier
Dynaudio Contour 1.3 2 way's "GLORIOUS Midrange and Presence"
JPS Labs superconductor FX Ic's
Tara labs Time and Space with TFA Return speaker cables
Transparent Power Plus Power cord &
MIT run of the mil powercord on the Llano power amp
I have no power conditioning whatsoever except some hospital grade junction boxes in which I have the CDP & Pre's hooked up-AMp straight to the wall.
Now I have experimented with various IC's and speaker cable Discovery,Cardas,Transparent..etc
I don't want to address this problem thru cable choice
I have changed the tubes in the CDP as well as the PreAmps
the Jps labs provides me with the transparency speed and extended Hi frequencies,,and resolution, but with noticable
sibilance could it be the Ac line conditioning or lack of it that is introducing the stridency and graininess to the sound? if so where can I start?
What brand power cables offfer the best shielding or get's the GRUNGE out? I've heard good things about coincident
I knwo that I should ( and AM in the process of)addressing the room itself carpet is in order and some accoustic paneling to kill the early reflections,should I do this first? then get the ac conditioning? has anyone had any experience with Marigo Powercords, shuyanta, Coincident etc.
Please offer me your suggestions
braab8
zaikesman
3,017 posts
 
Ezmerelda, Rives, and Esun are correct. You have a good system in a terrible room. Nothing you do to the system will be correctly quantifiable or justifiable before you address the room. A $200,000 system would probably exhibit the same problem in that room. Do a simple experiment: With a helper or two, try to carry on an intelligible conversation across your listening room for a while, separated by a distance about equal to your listening distance. Then relocate to your living room and try it again. Then ask yourself whether you may have experienced a reduction in effort and an increase in comprehension once you and your party moved out of the basement. Nothing in your whole system, other than the source material, has a greater influence on what you hear than the room. Start there, and you'll likely end there. Best of luck, keep us apprised!
reb1208
518 posts
 
Me

Let me tell you my friend. Your're problem is mainly- beyond the shadow of a doubt related to the quality of your electric mains. Phase anamolies between your tweeter and mid range driver have some effect. But just leave all as is. It's due to your local electric company.I can only listen mid September thru April. After that you might as
well spend your time with Budweiser. The above A/C remedy may help but best to leave it off. I do however have one consolation. If in a house. Place a ferite clamp on the incoming lead of your panel lead. do use cation.
bob_bundus
1,834 posts
 
AC line conditioning can go a long way toward allevieting sibilance issues in my experience. I use the Chang Lighspeed products, a 2500 for source components & a 9900 amp for (guess what) the amps. A 6400 ISO or a 9600 can do it all for you since you're not running large watts. Yes I also use upgrade AC cords & a dedicated AC line.
cdc
1,773 posts
 
So if testing the system at midnight shows no reduction in sibilants from the daytime, then it is not the A/C power. Power conditioning would not be needed. From what is being said here.
bob_bundus
1,834 posts
 
I don't agree with the timeclock theory. Noisy power is due to many possible reasons, not necessarily load-related. The only way to determine if line conditioning will help is to try it, using *decent* equipment (not the lowest budget cheapest thing that you can find).
More to discover