Any way to mod the TAD-803's ?

the amp may be a consideration here, especially when pushed harder. (thanks reg for pointing that out) i'm using a 50wpc updated vintage solid state amp, but in stock form (which it ain't) it has a damping factor of >200 and ~200wpc dynamic reserve. even before i get to the cabinet mods i can rock out at moderate volumes (taking physics into account as reg also points out). you can't expect too much from any bookshelf speaker, but an iron-fisted grip on the main driver sure helps.

First, thanks for the responses.

Cabinets- I agree, the cabinets seem overly light. I mean extremely so. I haven't taken out the drivers yet, so I honestly can't be 100% on whether there's no crossover. I'll try some of those mods.

to Reg- Unfortunately, I can't help but be a tad bit offended by your post. I don't expect the 803's to be tower speakers, and I'm not referencing volume nor did I ever in my post. The issue is that on more complicated pieces the 803s start to sound muddied, especially in the soundstage department. Now, if bookshelf speakers can't produce full orchestra pieces with any level of believability...then the audio world has some progress to make. But I'm not sure that's the case. I've owned several pairs of bookshelf speakers and even tested a pair of Athena bookshelves with the amp in question and had a more "even" experience across all genres.

As far as the amplifier is concerned...to imply that this amplifier is incapable of portraying any heavier pieces (be it symphonic, or metal) seems rather ignorant. And your implication about the design seems to state that the 202 is made for an opera audience while the higher priced amps are better for "teenagers". I understand that higher priced products from a company generally perform better than lower priced products. But an amplifier is an amplifier. It's not like comparing a violin to a snare drum. The bass response is adequate enough at 70hz plus (a subwoofer takes over here). ("Bandwidth: 17Hz to 140KHz + 3dB; 0dB = 40 W 1KHz") And the damping factor is most likely above 10 which many consider to be the "definitely good enough point".

To further extract the amplifier from the situation- In the beginning of my post I stated that I originally used a 135 wpc SS amp known for having strong bass/midbass performance. Yet I witnessed the same problem among genres using this amp. Acoustic/jazz sounded acceptable through the 803's - anything heavier slowly sounded worse and worse.

Conclusion-
I may just be being too picky. I'm not saying that busier/heavier music sounds terrible. I simply mean that in comparison to the almost beautiful portrayal of simple guitar music or light classical / jazz pieces heavier music just sounds slightly more lifeless.

Rob,

Just my .02 cents here, but have you contacted Paul Grzybek yet? Since he's the speaker designer perhaps he might be the person to talk to about your issues with your TAD-803 and which mods to make that would "heavier" music less jumbled.

Well, I took out the drivers and found that this is actually the crossover version. However, as they don't seem overly bright to me (with a tube amp), this is probably the better situation.

Do the SD units (the ones without crossovers) have better drivers? Or is the crossover simply removed. On the website it seems to imply that it uses a very similar albeit different driver.

Basically, do you think I could simply install a switch like the new 2007 models?

Cleaneduphippy - I actually did e-mail Paul and asked why the moon-rocks would fix the problems, and asked what else could be done. I've done some speaker design before, so I was curious as to how decreasing the volume would improve bass response, unfortunately I was thinking of sealed containers. (I might go to home depot and get 20 lbs of white marble then roll it in flour =P, just kidding on the flour).

He responded- "Moon Rocks are a specific material with real science based audio properties. (marketed like snake oil for fun!). They eliminate the cabinet side wall sound - place you ear against the 803 - you will hear eerie distorted midgange that comes off the cabinet walls (all speakers have some of this), mixing smearing the driver sound from behind. The rocks deaden this cabinet noise plus the rough sound absorbing rock mass stays piled at a 45-degree angle leaning against the back wall (other materials settle to the bottom, moon rocks stay in place). This rough slanted heavy back wall behind the port helps deaden cabinet noise. Moon Rocks will definitely aid the rock music cone confusion you mentioned. The bass from the 803 is relatively flat with a slight bump up. This bump up when driven hard competes with single driver midrange. Moon Rock cabinet volume reduction behind the port eliminates this bass bump - flattening it further, the cone stops gyrating out of control from cabinet noise backlash."

I'm not sure how it would deaden the cabinet noise, and he stated that it was not intended to couple the speaker to the ground better. I'm assuming the biggest effect is probably a cabinet volume reduction. It's possible that the speakers were originally designed with a box that was too big. Reducing the volume would reduce the qts and cut out a hump if there was one there. Unfortunately, unless the port length was also increased significantly, I'd think that this would effectively drop out a lot of the bass originally provided. With a subwoofer integrated, this may not be a real issue, but he didn't mention where the hump was located. If the bump is in the 85-90 hz region then there may still be a problem.

I opened the cabinet and noticed a few things.

A) There are two large wooden disks glued to the bottom of the box. I'm assuming that these were placed there for one of three reasons. 1) Perhaps this was originally a tweak to reduce cabinet volume after noticing the hump. 2) Perhaps simply to add more weight to the bottom of the box. 3) maybe an attempt to fix a resonating node on the bottom of the box.

B) The walls are very thin and corrugated to some extent. I'll probably try to add more structure to this using the putty advice previously mentioned. The walls are also made out of particle board as opposed to MDF board, this will naturally induce more resonance.

C) The driver isn't coupled to the cabinet very well. First off the screws were very loose (most likely so as to not strip the thin particle board wall). Secondly, there is no seal whatsoever, the metal backing of the driver is coupled directly to the laminate/particleboard. This might not be a big issue in vented designs. But it's probably better to over-design than to risk some weird leaks or vibrations. I'm assuming that the lack of any foam also transfers a lot more vibrations directly to the cabinet. (which I mentioned was very thin and resonance prone)

D) There are air leaks in the back binding post plate. Once again, this may not be a huge problem in vented designs; but it will change the frequency response somewhat, and may cause some noise.

Further Testing:
After doing some simple frequency analysis, it seems like the hump occurs at 90 hz with a slight recession at 100-110. Meaning a subwoofer won't do much to remedy the situation unless the crossover point is set to 100 hz (probably not a good solution). Presumably because I have the crossover design there is also a moderately large hump at 3khz, there's really nothing that can be done to fix this aside from changing the crossover manually or equalizing the original signal.

Some of these results may be skewed slightly by room acoustics, I'm simply reporting what I found in my specific case.

I purchased some putty, a little weather stripping and 50 lbs of gravel for $10 total at home depot. Let's see what happens.