Mapleshade Silclear


Category: Accessories

I'm not a big proponent of the "WOW" factor, meaning very few tweaks have caused me to go "WOW". The wow ones include rebuilding my McCormack DNA .5 amp to near Rev A, changing the caps in my speakers from Axon's to Sonicaps, and few others. Now that doesn't mean I don't hear differences and improvements with other tweaks, it's just that I don't believe in overemphasizing these differences into religous revalations and such.

So, Silclear doesn't fall into the "WOW" category with me, but it did make an improvement in my rig. The simplest explanation of these changes I can make goes like this. Have you ever cleaned the contacts on your interconnects, speaker cables and power cords after a year or more of ignoring them? Did you hear the improvements in transparency and quieter backgrounds? Well I just cleaned everything over the New Year's holidays with cotton balls and alcohol with an application of SST (to signal wires) and Pro-Gold (to electrical connections) afterwards. Now, in February I applied Silclear to everything in my system that has a plug, jack or socket. This means interconnects, speaker cables, fuses, all electrical jacks inside my amp & CD player and DAC, electrical cords, tube pins, phono cartridge pins, etc. The difference was as if I left all these connections to tarnish for a year or more and then cleaned them all again.

Now, given that I just did the cleaning I can conclude that Silclear took this one step farther than alcohol and SST. Things were more transparent and noticeably punchier. The bass was louder (dammit - I had to turn down the sub's volume and rebalance the bottom end again). Soundstaging and imaging seemed to be a slight/tiny bit more forward than before, maybe because things seemed a bit louder at the same volume settings. Tonally everything was still balanced, just more there in terms of detail and nuance and definition. But I also found that there was a sense of more "realness" to instruments, especially cymbals (hearing more brass with the zing), and voice (more in the room presence), and piano (more body and weight). The system sounded quieter too - i.e. blacker backgrounds (but this can also vary by time of day as the power grid changes).

Is this a "wow" review in disguise? Perhaps for many it is, but I already have a whole lot of transparency and realness in my system (see "Isn't Anything Stock?" for my system details). I now have more of that than before.

I really can't report that there were any bad aftereffects of the Silclear either. There's no way to undo the application easily (it's a grease), so there's no A-B testing available. So many tweaks improve on thing at the expense of another - not here. It's a good thing (thank you Martha Stewart, now go directly to jail and don't pass "GO").

Enjoy,
Bob
ptmconsulting
So sorry for any conveniance. SilClear is an exciting product and I was certainly convinced of its importance. I never would have suspected the problem when I first used it. As I stated my audiophile friends and I were blown away for many months and treated our entire systems.
I'm hoping to experiment with it again, just on the power cord connections in my sytsem. I'm going to follow this protocol.
1. Carefully clean the contacts with Caig DeOxit and Gold.
2. Place the lightest, finest coating possible with Sil Clear.
3. Leave the cords plugged in for a month or two, then clean the pc connections and try listening again.
As I recall, I did not clean my connections orginally very carefully before applying SilClear and maybe this accounts for the problem.
4. I think I'll call Mapleshade and talk with Pierre.
Again sorry my rantings may have caused paranoia.
Sgr
Well its good news and bad. I am very happy to hear that other careful listeners noticed so much improvement in thier systems also. Yet I now too await the degradation.Perhaps I will get lucky in that I did fairly carefully clean my connections before applying and used a thin coat.
The product recommends putting SilClear only on the male part of connections, so I can see how to clear that off. But of course once the connection is joined the Silclear is now on the female part as well. Do any of you with experience have suggestions on how to clean the now contaminated interior female parts? Sorry this post is so pornographic.
I just blasted the interior of the female parts with Caig DeOxit until all the silver disapeared. I assume it was all removed.
SGR,

Have you spoken to Pierre about the degradation? I've yet to apply the Silclear.

Ken