Confessions from a VPI owner of some 30 years


I would like to start with a humble apology to the OP of a thread I recently (overtook) for personal reasons. smrex13, I apologize to you and hope your audio journey going forward is joyous!

To donvito101, I made my remarks personal and for this I apologize.

I checked for remarks from yesterday on the "VPI Prime noise issues" (2 threads, why, I don't know) . I still find it odd that VPI did not remark on smrex13' original thread, only to his last thread that ended, "not VPI's fault".

I've had a couple of issues since purchasing my VPI Classic 3 SE Sig. one year ago. I sent, (through my dealer), an initial question about the arm tower's operation on Feb 2016. I was told it would be forwarded to VPI. As of today, I've not received one comment.

I've recently, in the past 3 months, had a vibration issue through the 3D arm when the SDS is set at 33rpm. It is not noticeable at 45 rpm. I feel it through the finger lift.

I've tried oiling the motor, cleaning the belt & new talcum, the spindle bearing is just like recommended with the proper grease etc...

I relayed all of this through my dealer who asked for pictures and I sent them. This was two weeks ago. As of today, not one word. Because of my last question through my dealer in Feb w/ no response, I'm a little weary.

OK. So, my position is.... I should go through the proper channels. The dealer, right? VPI has their sales set up through a dealer network. This, I assume, is to take a burden off of them so they can be focused on manufacturing?

We/I/ you, pay a premium for this? I assume it's around 100% added to the actual cost of manufacturing. So, if I have an issue, I should follow the way VPI has their dealer network set up and take my concerns to the dealer. If this is not the way things should work, why then, doesn't VPI just sell directly? We/me/the end user could save BIG BUCKS.

That's pretty much the whole issue. I have no idea why VPI does not want to make any effort to settle this issue.

Cheers!






128x128slaw
If I'm correct in that VPI has or will be discontinuing the SDS, it seemed that accepting the ADS was a better option at the time. Again, no one offered an explanation.


I'm not surprised they weren't able to fix the SDS, I don't know who they have working for them that could repair a piece of digital equipment such as that.    AFIK, the SDS has been discontinued, but all of the ICs and PCB components are still available;  the power supply is a SMPS type and there are many good candidates for replacements if the original is not available.  What was wrong with it BTW?  I suspect I may be able to fix it via e-mail and some minor soldering.

I'm also not surprised that the ADS is off frequency or that it drifts with time.  It uses an analog oscillator which subject to drift with temp and time and will be nowhere near as accurate or stable as the crystal controlled SDS.  It looks as if they used the same output scheme as the SDS (small PCB mount heat sinks) so I think the heat build up inside the case will be significant and cause the frequency to drift.
With the outpouring of (love) ....IE: inviting you over and such, after your previous posts... and your gushing over their new customer service..

With this sort of customer satisfaction, it would seem to me that I'd get...at least an email or a call asking how the new ADS is performing?

Something just doesn't add up?




phoenixengr,

I wasn't informed as to what this issue was. I wasn't contacted at all during the time they received the unit until almost two weeks later I inquired an update!

Their whole scenario is SUSPECT.

Frankly, I thought I was doing well, at this point, to even get some sort of customer service!

I just want to listen to music. I thought I'd be able to do so with a well reviewed tt by all of the press with this table.

It seems to me, even more now, that I was still, taken advantage of.