Throughly disappointed with my new Yamaha A-3000 Integrated.......


well, I love it when it's not shutting down.  Finally called the dealer and told them I'm done with it.  From the first day, it shut off and went into protection mode after 10 minutes of listening.  It's doing it all the time now.  I did figure out how to reset the amp, but it continues to go into protection mode.  Here's what I've done to track the issue down.  Am I missing anything?  By the way, I'm a user, not someone who can track down voltages, test wires etc etc.

1. Pulled power cord for 30 minutes- I use a PS audio PC
2. Unplugged all connections- amp stayed in protection mode with nothing plugged in.
3. I then figured out how to reset the amp.  The amp then worked for for some periods before shutting off.  Yesterday for example, playing vinyl, amp shut off after 5 minutes.  I then did the reset and listened for 2 hours without shutting down. 
4. Today, after 5 minutes it shut down again.
5. Doesn't matter if it's vinyl or CD playing.
6. I just unplugged my Sub now as the rca cables are a bit bent up; however it didn't affect play for 2 hours yesterday without shutting off.

Disappointed as I was looking forward to breaking this in over Christmas break........  
128x128dhpeck
Regarding Sub connections:  

"connecting a sub to the speaker terminals of this amp is a no no"

Can you run a connection from the terminals on the speaker to the sub?
My sub only has 2 RCA connectors in which I connect to the pre-out right/left on the amp
honeybee2012, I would error on the side of caution and NOT hook an active sub to the terminals of the speaker if that speaker is connected to the AS3000.  From the Yamaha AS3000 Manual:

CAUTION

Because the power amplifier of A-S3000 is of the floating balanced type, the following types of connections are not possible.

Connecting with the left channel “–” terminal and the right channel “–” terminal as well as “+” terminals (Fig. 1).

Connecting with the left channel “–” terminal and the right channel “–” terminal inverted (cross connection, Fig. 2).

Deliberately connecting with the left/right channel “–” terminals and metal part on the rear panel of this unit, as well as accidentally touching them.

Do not connect your active subwoofer to the SPEAKERS L/R CH terminal. Connect it to the PRE OUT jacks of this unit.

Do not connect a component with no volume control, such as a CD player, to the MAIN IN jacks, as the volume level of the signals input to the MAIN IN jacks is fixed. If such equipment is connected, a sound may burst, and the unit and/or speaker may be damaged.


Can you run a connection from the terminals on the speaker to the sub?
No, absolutely not. That would result in the same issues that would occur if you connected to the amp’s speaker terminals.

However what would probably work ok, depending on the specific design of the amp, would be to connect the + inputs of the sub to the + outputs of the amp, and connect either or both of the - inputs of the sub to a chassis screw on the amp. (I’m assuming here and in what follows that one sub is being used, rather than two, and that the sub provides inputs for two channels). That is what REL recommends for their subs when connecting at speaker level to an amp having balanced or bridged outputs.

I can’t envision a design for which that approach would cause damage. The worst thing that might happen, depending on the designs of the amp and the sub, would be a loud hum. But chances are it would work ok.

An even better approach would be to solder one or both negative wires from the sub to the ground shell of an RCA plug (or optionally two plugs, using one for each negative wire), leaving the center pin unconnected, and plugging it or them into an unused RCA input connector (or connectors) on the amp. In the case of the A-S3000 and other integrated amps providing "main in" connectors, it would probably be preferable to plug in there, rather than to an input intended for a source component, since that figures to provide a more direct path to the ground of the amplifier section.

In cases where the sub provides speaker level inputs for two channels I suspect it wouldn’t make any difference whether one or both negative input terminals of the sub are connected, as the two negative input terminals of subs which provide two input channels are most likely connected directly together within the sub.

Regards,
-- Al