Why are my woofers pumping?

@o_holter : Again:

https://forum.audiogon.com/discussions/why-are-my-woofers-pumping/post?postid=1551771#1551771

With all respect to those gentlemans that insist on the KAB filter or the like please ask you: who of them owns the Atlas or even listen that kind of very high quality performance levels?

Seems to me that no one of them because they are not taking in count what really means: quality level performance at the Atlas levels- They say that with the filter they almost did not listen degradation and this just makes no sense.

R.

Almarg 4-24-2018
... given the unusual design of the turntable’s drive mechanism (comprising six belts, three of them driven by what is apparently a synchronous motor on one side of the table, and three of them driven at a different height by a similar motor on the other side of the table) ... the platter might be being driven in a slightly uneven and/or not perfectly level manner. Perhaps simply due to the condition of the drive belts differing slightly between the two sides.

And I note from your system description thread that the table appears to be around five years old. Perhaps all that is needed to resolve the problem is a new set of belts?


Cleeds 4-28-2018
That actually sounds very much like a drive problem, such as a bearing issue or bad belt.


Atmasphere 4-30-2018
Boy, that sure sounds like a drive issue to me!

Consider replacing the belts!

Best regards,
-- Al

Correction: the Atlas has a 121 ohm load (not 100) - and sounds fine.
Replacing belts - yes, new ones ordered.
I will give the spindle a drop of oil, and fasten the spindle housing when I get the right tool.
BTW, reading up on the Hifi News test record shows that people find a lot of problems with it. On the lateral resonance test the actual test tones are different from those stated. I know from before that the record's anti-skating test is not good, in my case at least.
Some years ago Michael Fremer reviewed the Kuzma 4-point with his Lyra Titan i cartridge, pronouncing it the best arm he had heard so far. But using the calculators, resonance is down to ca 7.2 hz. Even more problematic than with the SME V (ca 7.5), since the 4-point weighs a bit more. Yet it wasn't a problem, to his ears.

Hi Raul, thanks, I reread your former post, where you wrote: "even at 100hz the Atlat compliance and effective mass puts the resonat frequency in a " solid " 8hz."  I get results closer to 7hz (arm mass 10.5, screws 0.5, cart 11.6g). It all depends on what we assume is the 10hz measured compliance (supposed to be x 1.5 to x 2 of the 100hz measure - 12 in the Atlas case). I have to assume a compliance of 17 to get above 8hz. I have found no exact Lyra specification. So this is really "blind", especially if we assume - as some do - that small variations in resonant frequency play a role, at the margins at least. I get confused by all the web debate on this, "fundamentalists" who say resonance is of key importance, some who say it varies with the type of arm, player, and what not, and some who simply dont believe in it (at least not with modern fairly "medium" cart/arm combos).

Likewise, I can find no objective measure of how much the resonance increases, by adjusting the static counterweight so it does all the lifting on the SME V, compared to using the dynamic spring mechanism (but a lot of debate about how the dynamic may sound best and be more kind to the cartridge). I do see the point of Lyra including light weight alu screws (among several types). Regardless of their problems, both the Hifi record test and the calculators indicate that the arm could be lighter.

So - back to the ears? Only listening can really be the judge? Test records not correct, calculators failing to take into account important parameters  - like the arm stiffness - you name it.   

Some of you have suggested that acoustic feedback may have played a role for my "woofing" or woofer pumping.

This is relevant not least in a four speaker system, like mine, where some drivers are pointed towards the back wall  (with the record player).

I tested a bit more, playing the new 2 x 45 rpm Jefferson Airplane: Volunteers. Volume: loud. This is a very good remaster, quality pressing, low vinyl noise. I hear this on the grooves between the tracks. When the tracks / music played, I used my stetoscope on top of the different parts of the player.

The results were interesting, more varied than I would have thought. The top of the maglev feet had next to no feedback, the sound was dead. The plinth, and also the motors, had more feedback, although I did not hear clearly "wrong" or exaggerated sound. I tried to "hold on" to the plinth, firmly, as suggested in the thread above. It made no difference.

I would like to test the platter and the record clamp, but since this rotates, I can’t do it with a stetoscope. Anyone knows of a phone app to test for rumble or noise, laying on the platter?