2. cables
  3. 140965-81298

To buy grounded or not to buy grounded. That is the question.

I recently happened on to a highly recommended web site and looked at power cord options.  There were two basic options: grounded or non-grounded.  Below is the copied info from the non-grounded cord page.

----------------------------------------------

"Description
Non-grounded cord  (Ungrounded, the ground wire is removed from cord, with G-plug still intaked)

WHY?

Based upon measurements and listening tests; I have recommended to people, to ground only one piece of their interconnected equipment. The interconnects will provide static dissipation through the secondary ground connection & nuetral. They often look at me in extreme terror.😱

Wikipedia agrees…

Wiki; A ground loop is the result of careless or inappropriate design or interconnection of electrical equipment that results in there being multiple paths to ground where this is not required, so a complete loop is formed. In the simplest case, two items of equipment, A and B, are each connected to a wall socket by a 3 conductor cable, containing a protective ground conductor. This becomes a problem when a interconnect cable is connected between A and B, to pass data or audio signals. The shield of the data cable is typically connected to the grounded equipment chassis of both A and B. There is now a ground loop.

How can you benefit from this? Purchase the Grounded cord to hook to your preamp or integrated receiver…All other power cords in the system, such as source equipment, dacs, amplifiers, subwoofers,etc. should all use the non-grounded cord.  This will direct ground your system, removing hum and reduce harmonic distortion from your system. We’ve seen multi thousand dollar power conditioners that do not fix or address this issue. The issues of ground loops are often greater then the dirtiness of the actual AC power!



Need More?

Hot: The black wire is the hot wire, which provides a 120 VAC current source.

Neutral: The white wire is called the neutral wire. It provides the return path for the current provided by the hot wire. The neutral wire is connected to an EARTH GROUND!!!

Ground: The bare wire is called the ground wire. Like the neutral wire, the ground wire is also connected to an earth ground. However, the neutral and ground wires serve two distinct purposes.

The neutral wire forms a part of the live circuit along with the hot wire. In contrast, the ground wire is connected to any metal parts in an appliance such as a microwave oven or coffee pot. This is a safety feature, in case the hot or neutral wires somehow come in contact with metal parts. Connecting the metal parts to earth ground eliminates the shock hazard in the event of a short circuit. (KEY WORD IS SHORT CIRCUIT, Meaning your electronics are broken!)"

----------------------------------------------------

What think ye of this?

Toolbox149

toolbox149
jea48
4,463 posts
 
+ 1 what cleeds and spatialking posted.

"Description
Non-grounded cord (Ungrounded, the ground wire is removed from cord, with G-plug still intaked)
Power cord is not Listed by any 3rd party testing laboratory.

in case the hot or neutral wires somehow come in contact with metal parts. Connecting the metal parts to earth ground eliminates the shock hazard in the event of a short circuit.

It also provides a low resistive path for ground fault current to return to the source in the event of a hot Line to chassis fault. A hot to chassis fault will cause an overload in the equipment AC line fuse causing the fuse blow breaking the fault circuit. (Fault on load side of fuse) If the fault is ahead of the fuse the only protection then is the branch circuit breaker that protects the branch circuit wiring. No way, jmho, the small wire of an IC will handle possibly over a 100 amps of inrush fault current.

Based upon measurements and listening tests; I have recommended to people, to ground only one piece of their interconnected equipment. The interconnects will provide static dissipation through the secondary ground connection & nuetral. They often look at me in extreme terror.😱
Sounds good but has anyone run any tests or experienced an IC carry, handle, the ground fault current in the event of a hot to chassis ground fault? You might want to look at the wiring schematic diagram of your audio equipment. Good chance you will find the signal ground is not connected directly to the chassis.

Even if the IC can handle a high current inrush ground fault will the signal ground circuitry of say a preamp be able to handle it long enough for the AC line fuse in a power amp to blow open?
Jim
erik_squires
16,202 posts
 
Under no circumstances should you remove a power (i.e. safety) ground when the manufacturer provides for it.

Certain devices with removable cords do NOT require it, as evidenced by the IEC connector having only 2 prongs. For instance, my sub woofer.

The Pangea cables with removable ground pins are a safety hazard in multiple ways and should not be purchased or used.

You may always use a grounded cable for an ungrounded device though.


erik_squires
16,202 posts
 
Based upon measurements and listening tests; I have recommended to people, to ground only one piece of their interconnected equipment. The interconnects will provide static dissipation through the secondary ground connection & nuetral. They often look at me in extreme terror.😱

A little knowledge is a dangerous thing, and in this case potentially lethal. Do not follow this advice.

Based upon long term driving comfort, and gas mileage I’ve decided to remove the air bags and seat belts and spare tire from my car. I’ve never had a problem, and I save money thanks to the car being lighter.Plus, my daughter really likes riding on my lap instead of her baby seat.

That’s what this is.


stereo5's avatar
stereo5
6,414 posts
 
I would bet those ungrounded cords are not U L approved.  Should one of them catch fire, would the homeowners insurance cover it?  I am willing to bet they wouldn’t. 
Ag insider logo xs@2x
cleeds
5,967 posts
 
stereo5
I would bet those ungrounded cords are not U L approved
They're probably UL listed. There's nothing inherently unsafe with a two-prong power cord. It's using it on a device that is designed for a cord with a safety ground that's hazardous.
Should one of them catch fire, would the homeowners insurance cover it?  
It would almost certainly be a covered loss. Carelessness isn't a typical exclusion.
More to discover