2. analog
  3. 150758-92835

Trans-Fi Terminator Tonearm: 2019 Update

In reading a few related posts on linear tracking tonearm, in general,  and Trans-Fi Terminator , in particular, I thought I would give a brief update of the Terminator.

I purchased the arm directly from Andrey in Moscow two months ago. From what I understand, Andrey has taken over production after Vic's retirement. What I received is the most up-to-date version of the arm with the carbon fibre wand and brass counterweights, the direct wire leads from cartridge to  phono amp, and a new brass manifold ( not evident from the main web-site). Both the wand and the new manifold are Andrey's contribution to the continued refinement of the Terminator.

Also,  please visit this site: https://darklanternforowen.wordpress.com/2017/04/15/terminator-tonearm-new-arm-mount/. This gentlemen from NZ has developed a new arm mount for the Terminator which advanced the arm's sonics even further. It was reading through the the development of this new arm mount that convinced me to order the Terminator after much prior research. I did not purchase the arm mount from NZ as it would not readily fit my Verdier La Platine, instead Andrey made a custom arm mount. It is in essence a two point support mount rather than a single point support rod that is commonly used. 

My previous arm was a SME V of 1990's vintage mounted with a ZYX airy. The Terminator is several notch above the SME V. All the accolades given to the Terminator seem justified. My main point in writing is that the new developments by Andrey, i.e. the carbon fibre wand and the newest brass manifold, seem to improve upon the Terminator even more ( see link above ). This is the news that I wanted to share with existing Terminator owners. I asked Andrey to start a blog on all the new stuff that is happening with the arm, but it seems that he is busy making 'things'!




ledoux1238
ledoux1238 OP
283 posts
 
Yeah, and I only have the regular copper run...  :(

@ bdp24 As for the LFT 8b’s, I’m gonna take it slow. Exploring OB subs would be the next phase, though your input is much appreciated. 

Of the audio companies you mentioned above some are unfamiliar to me, so more research.  But Townsend audio I’m quite intimate with. I owned a Rock V TT for many years, purchased based on, among other considerations, a review by Robert Greene ( again ). Innovative, good sounding, and not very expensive were some of attributes, kinda like the the Terminator.
terry9
2,342 posts
 
I've been using the Terminator for 5 years now, for the last 3 on an air bearing TT. Interesting about the brass manifold - though I've never had a problem with the aluminum. I use a HighBlow air pump with a cotton buffered surge tank, precision regulated to 30 mm of mercury, which is about 1/25 atm or just over 1/2 psi. The saddle skims beautifully over the manifold just like any other high class surface over a high class air bearing.

It tracks fine at 10 mmHg, but sounds livelier at 30. Above 30, no improvement.

For the record, if you increase the mass of the wand with brass weights, you can run very low compliance cartridges, e.g. higher end Koetsu. Don't really know if silver cables are better, but you can't have mine!
terry9
2,342 posts
 
@slaw 

About your appliances - if you do decide to move, let me know if you want to sell your compressor. I've been thinking of upgrading mine.
terry9
2,342 posts
 
@harold-not-the-barrel 
@ledoux

I have a Fozgometer, but don't use it. For me, it's both easier and more effective to set azimuth by ear. YMMV 

ledoux1238 OP
283 posts
 
@terry9   Pray tell which air bearing TT?

The Terminator seems more sensitive to all the adjustment variables, VTA, azimuth..etc,  to a degree that is previously unknown to me. I seem to be adjusting  VTA much more frequently. Different records really do sound differently without fine adjustments. It is certainly more sensitive than my previous SME V, to a point that I question if I had ever set up the SME correctly!

I also don't have a Fozgometer. But through a few simple adjustment of the twin pivot bearing at the wand, you could hear distinctly the altering of  channel separation , sound-staging, and imaging. I am in effect setting azimuth by ear. However, I would like eventually to get a hold of a Fozgometer  just to verify.

The way the pump affects the sound is something I will have more questions on in the future. But thanks for sharing!

More to discover