2. analog
  3. 153260-132884

Cartridge, Compliance, try what in my JVC UA-7082 Arm?

So, what to try in my new JVC UA-7082 Tonearm when it comes? (effective length 282mm) (11-1/8")

Guidelines? Advice? (I never bothered learning about compliance, I guess now's the time).

Anyone know the Mass of the UA-7082 Tonearm without a cartridge _______?
.....................................

Self Imposed Restrictions:

High Output, 4.0mV or more (to avoid tube preamp hum zone until it's repaired).

MM Only. (I am fundamentally opposed to MC pre-pre amp, as well as needing high output).


.......................................

Motley Crew On Hand:

4 headshells, none special

Shure MicroRidge Stylus and V15VxMR Cartridge

Shure V15VMR Cartridge (no stylus, I gave it a dirty look and it broke, horribly brittle shaft)

Shure 97xe Elliptical Stylus and Cartridge (despite it's low pedigree it's my current favorite).

Shure N78S Stylus (fits 97xe) (I did not inherit the 78's someone threatened me with).

Shure M44E Stylus and Cartridge

Audio Technica MicroLine AT440ML OOC Stylus and Cartridge

Audio Technica AT7000 body, no stylus

Audio Technica ATP-2

Audio Technica Series VIII P mount 

Audio Technica ___? Came with the AT120 TT (tracks 2.5g, I never used it) 

................................
It's a busy time, it doesn't get here till mid Jan, so theirs time to research.

Thanks in advance, Elliott






elliottbnewcombjr
chakster's avatar
chakster
6,144 posts
 

$400?

The uber can be the smartest guy on the planet, but we’re talking about NOS STYLUS, not about a set of Victor X-1IIe/D (cartridge, stylus, headshell) in mint condition. I do not promote my listings here as many other people do, and ebay prices are at least 15% higher than it can be on other sources online.

I think realistic price for a NOS stylus with titanium pipe cantilever is about $400 for this model (just for the stylus) and this is about the same price that ANY re-tippers charge for their frankensteins. Comparing an original stylus with exotic cantilevers to some fake styli with aluminum cantilever for $260 i would always buy an original if i could find one. I did find a few, so i hope it is not impossible for X-1IIE model, but much more difficult for X-1II.

I have all these cartridges, styli, tonearms etc in my collection.
All of them in multiple samples, it was important for me to check and to compare all of them in my system.






chakster's avatar
chakster
6,144 posts
 
Anyone can join discussion about Titanium Pipe cantilevers, i can only recall Audio-Technica cartridges with this type of cantilever, but we're all aware of the Boron Pipe and the reason why they are better.   

According to our member @simpikins5 and his inside the beryllium is the best (no wonder why the most expensive Victor has beryllium cantilever): 

"There was a thread on Audiogon quite a while ago in which a former engineer from Audio-Technica was participating. He wrote a rather in depth post as to why Beryllium was the go to material for cantilevers and the panic that ensued at AT when the EPA came down with the order that it no longer be used due to the dangerous toxic dust released when machining the material. He stated that the engineering department underwent a lot of R&D to find a suitable replacement material and Boron was what they determined would be closest, however it was still a compromise. Apparently Beryllium allows for the largest frequency excursion without distortion and also permits better channel separation and signal to noise ratios. This is why it was so good." 


uberwaltz's avatar
uberwaltz
13,381 posts
 
Chakster.
I know it has been mentioned before but honestly where in tarnation do you manage to find all these exotic carts and stylus at relatively bargain bin prices?

I am serious, not jerking your chain as I would love to try some but unless I take a chance on some ex Japan stock I see nothing usually.
Thank you.
lewm
13,087 posts
 
Chak, If you say you are not the person selling the Victor cartridge in the eBay ad posted here by someone else, I will believe you, but the use of the English language in that ad is very reminiscent of your phraseology, and you are located in St Petersburg, are you not?  (Maybe you're not.) Do you know the seller?

As for the wonders of beryllium.... beryllium, shmeryllium.  As you know, I have Acutex 320 LPM and M cartridges that use titanium cantilevers.  They are as good sounding as any other cartridges I own, MM, MI, or MC types.  When I brought the Acutex cartridges up in the past, you were dismissive. As you also know, I don't judge cartridges solely by the materials of which they are constructed.
elliottbnewcombjr OP
5,448 posts
 
I never said original stylus.. I would not pay that much even if I found one as rare as that.

My question remains. Is x_1IIe Body internals SAME as x-1II body??? 


More to discover