2. tech-talk
  3. 155706-144095

TEAC NT-505 impossible connecting to WiFi router o such LAN: help me please?

Hello mates,
I got my NT-505 3 days ago.
It seems to be working correctly but in my opinion all software in not the same level than the device: too aged & often no relevant documentation or support about.
However my big trouble is the NETWORK interface:  since first time I switched on, the NT-505 remains "for ever"  into NET configuring blinking state until it goes in power stand by.
Summarizing:

1. RJ45 cable is ok - tested in several manners
2. the wifi router (1Gb fiber connection) is ok
3. the wifi router ether ports (4) are ok - I checked a bridged LAN configuration too

Testing the NT-505 Ether port It results:

1. the physical level of protocol seems working correctly just on-way: the interface recognizes correctly the bandwidth (Fast ot Giga in my case) end the packet coming from the router are buffered. No packet sent  to the router.

2. At protocol level no ARP session are involved hence impossible retrieve MAC address and trying to do something.


VERY STUPID ISSUES:

1. Being NET board logically split from MAIN board It's need a separate firmware(!!!): how can I upload the NET firmware if, as stated into documentation, I must use the mobile app and It's impossible connecting the device to such LAN?

2. NO menu interface to configure manually the net parameters.

May someone help me (tricks..., recovery sw,..., low level maintance menu...,...) 

Thank you a lot.


silvio66
audiojedi
225 posts
 
Just to be clear - from what I understand you can update the NETWORK firmware through the app and over the network but to update the SYSTEM firmware you have to download a file on a home computer, unzip the file and then connect the home computer directly to the NT-505 in order to update the SYSTEM firmware.

I had to pull my NT-505 from my audio rack and connect it directly to my PC in order to update the unit have you done this?
kren0006
1,859 posts
 
Make sure to use Lumin software app, not the Teac software app for control. Lumin app is more stable and is compatible with the player.

I also haven’t had any trouble with my NT-505. Although I did have trouble initially updating to current firmware version. I was connecting to the USB (the larger one labeled USB) on the back rather than the micro USB (very small, unlabeled, near bottom), but once I figured that out it was good. Sorry can’t tell from your last post whether you have successfully updated to current version or not.

@audiojedi did you mean version 1.21 firmware, or did your really mean 1.22? Isn’t 1.21 the latest?
EDIT:  Nevermind, I see that 1.22 came out now.

OP, sorry for my basic descriptions but you know the NT-505 doesn’t have wifi, correct? It is Ethernet only. No wifi. I think your references to wifi in your post refer to your wireless router, just wanting to make sure you got that which I’m sure you do.
kren0006
1,859 posts
 
Correct, what audiojedi said. It says it is doing an initial update when you initially get going but that is just the phone app.

To do the firmware upgrade to the NT-505 itself you need to use a PC (not mac) and use a physical cable to connect to the little micro USB port on the back at bottom just above the word "Digital" (which is confusing because the "Digital In" label refers to the optical input, not the micro USB, which isn’t labeled).
silvio66 OP
13 posts
 
I understood that I did not explain correctly my issue: my problem is not the FIRMWARE upgrading via usb rear port (already done several times)
My NT-505 DOES NOT establish any connection to LAN  via Ether port (no protocol session starts hence no IP@ is assigned to NT-505 port by the router) 
In this condition the device results unreachable by anythings running over IP protocol (apps included). This means that I'm looking for an alternative method in order to upload the NETWORK fw.

Summarizing:

SYSTEM FirmwareV1.22 -> done (from japan site) and running correctly

NETWORK FirmwareVer11.6c ->  not possible because It seems that via app is the only manner to do this.

I have two hypothesis:  shipped without network fw on board or such chip managing the Ether port does not work.


djones51
4,947 posts
 
Might check if your  router is set to hand out IP addresses by DHCP. Looks like the Teac is trying to get an address and is timing out. Other than that you could try Teac support it could be a bad chip.
More to discover