2. speakers
  3. 161159-128699

Question regarding subwoofers

I have an RHLabs SB-1 that’s served me pretty well for many years and use with it with my Acoustat 1+1s. (Had it refoamed a couple years back.) As well as the 1+1s image, I’ve always been slightly annoyed by having a single subwoofer between the panels. When playing something with a large sonic image like orchestral music the setup works fine. However when playing something more intimate like Jazz it’s easy to "see" where the lower frequencies are coming from: The middle. As my listening has gotten more refined it’s getting to be less acceptable to me. So I’m looking possibly at a pair of smaller, powered subwoofers. Why powered? Simple: If I do this, I’d rather the ARC VS-110 just power the panels. So, my questions:

1) The SB-1 has a single 10 or 12" driver. I’ve seen subs anywhere from 8" to huge. What folks experiences been with a pair of 8-10" powered subwoofers? Too much? Not enough?
2) Did a pair of subs affect imaging much? IOW, could you discern enough left/right to make it worthwhile?
3) How tough was it to balance them?
4) Do I run another set of interconnects from my SP11? Or do I get a set of Y adapters to feed both subs and amp?

Let me close by saying that like with most things audio there’s going to be a lot of "it depends". I get it. But I’d still like to hear of folks’ experiences as I do see a lot of systems with subs.

As always, thank you much for your time and comments!

128x128musicfan2349
wolfie62
353 posts
 
I have a single 8” dual vc Velodyne DLS (Servo) powered sub. DSP crossover. Remote control. -3 dB at 32 Hz. I have it crossed over at 100 Hz. Bass always sounds like it’s coming from wherever the imaging says it should be, whether center, back, left or right.  Plenty of clean and articulate bass for me. My main source is vinyl; very few LPs go below 30 Hz, so it’s perfect for my setup and my tastes. I listen to all kinds of music, mostly. I just can’t justify these other bass everywhere setups.  
m-db's avatar
m-db
986 posts
 
Some subwoofers offer a great deal more in the way of calibrated filtering and  adjustability without digitizing the rest of the system and may satisfy your needs in your room.  

I believe jrwaudio's SVS Ultra has an easy to use auto setup process that also allows the user to manually tweak things to taste as well as some adjustable presets. Check out the Ultra User Manual on line. You'll get a better idea of useable modern processing and connectivity. Have fun with it.

geof3
1,129 posts
 
@musicfan2349 if you can easily locate your sub in your room then it is not integrated well, one way or another. Either crossed over too high, gain too high, or some combination of placement and the others. Some rooms are very tough to nail, and that is where the multiple sub concept works. It is possible to integrate a single sub and make it “disappear”, but that requires speakers that dig down pretty low and a cooperative room/setup. Overall, it is much easier to get 2+ subs to integrate as a whole. But one can be done...
bdp24's avatar
bdp24
9,846 posts
 
Using 80Hz as the x/o frequency is not the whole story: what’s the order of the filter? A 1st-order filter is only 6dB/octave. A sub so used is still putting out a lot of sound at 160Hz (an octave above 80Hz). If using 80Hz, the filter must be very steep, like 4th-order (24dB/octave).
lalitk's avatar
lalitk
5,569 posts
 
“However I must disagree with your implication that bass is non-directional. I have moved the subwoofer in the past to different locations and please believe me when I say that I could tell you where it was (and wasn’t) in the soundstage.”

OP, It appears you missed the whole point. If your system is properly calibrated, you won’t be able to localize main speakers or subs in the room from your listen chair (sweet spot). Please read it again what @millercarbon and others are saying. And yes, two subs are always better than one (small or large) if you can’t accommodate 4 (DBA or Swarm setup).

“The one thing that really matters is the one thing you don’t mention: crossover frequency. It should be below 100Hz, and 80Hz is even better.

This is because bass this low in frequency, you cannot localize it. If a sub is putting out any energy above about 100Hz you will localize it and that is why your bass seems to be coming from one spot.

Below 80 you can’t tell where the sub is, you can only tell there’s more bass. Where the bass is coming from, your main speakers provide those location cues. Also since you can’t localize there is no L and no R.”


More to discover