2. amps-preamps
  3. 162284-76532

Purifi Class D: Junk?

So, from the previous thread about high-end class D the Purifi module was brought up. I decided to get a cheap example from VTV, a simple stereo unit with a single Purifi module and matching Hypex SMPS. Standard input buffer. I got it in yesterday. First impression wasn't what I was expecting: weak, congested dynamics is what stood out to me. I expected greater expression through my ProAc D30Rs. The other problems such as poor soundstage, thin / boring character, etc, I marked up to needing burn-in before evaluating. So it's been 24 hours, I would still expect to get at least the high control / damping of high end class D and dynamic power, but it's just not present.

Could it be an impedance mismatch? Other manufacturers selling the Purifi with their custom input buffers are reporting 47k Ohms. VTV doesn't say in the manual or on the site. I checked the Purifi data sheet which reports...2.2k Ohms on SE???? That can't be right?? That's absurdly low! Am I reading the right spec? My preamp has an output impedance of 230 Ohms. Can someone confirm that the stock Purifi has this ultra-low input impedance?
madavid0
tweak1
3,666 posts
 
GFi
I never said they aren’t stupid expensive for what they are, but I have used many different versions of hi-end fuses over my DECADES as an enthusiast and as a B & M dealer back in the early 2000s (Audio Tweakers), so any name connection to evs is a coincidence

Once again you assume too much
milpai's avatar
milpai
2,395 posts
 
Alright, it is "sunshine from down under" on yet another Class D thread.Problem with george is, he feels we should trust his hearing and not our own.
Ask him for concrete evidence on Class D stuff, and he will cry uncle and start posting Nelson Pass's quotes. He does not have the full knowledge of class D. If you don't believe me, just wait for this thread to move on a bit OR go to other class D threads. And on top of that he calls on others as "policing" when he does the most himself. Looking at his past posts, I think he has some issues. Like digging up 13 year old posts and start calling out names. I suggest, ignore his posts and move on.
nd1der's avatar
Ag insider logo xs@2x
nd1der
43 posts
 
But watching audiophiles snipe at each other is more fun than watching politicians snipe at each other. Occasionally audiophiles agree on something.

twoleftears's avatar
twoleftears
5,318 posts
 
Yet another derailed thread by a few perennial posters who keep on repeating the same things, over and over and over and...  At least this one wasn't much of a loss, because of the false initial proposition on which it was based.
georgehifi's avatar
georgehifi
10,312 posts
 
Ask him for concrete evidence on Class D stuff, and he will cry uncle and start posting Nelson Pass’s quotes.
Shows what you know, think before you show your lack of................
That’s for an entirely different audio product not class-D. Stuff I post on Class-D’s Achilles-heel has to do with switching frequency and it’s filter and noise

But seeing you bought up Nelson Pass’s quotes, here are his on Class-D, that I’ve never put up.
Nelson Pass (Threshold, Passlabs)
"Does a $10 bottle of wine compete with a $100 bottle? Of course it does, and it often wins based on price. Right at the moment Class D designers seem to be still focusing on the objectively measured performance of their amplifiers. I expect that at some point the economics of the marketplace will encourage them to pay more attention to the subjective qualities, and then they will probably play a greater role in the high end."

And just for good measure Conrad Johnson
Lew Johnson (Conrad Johnson)
"I tend to think that Class D circuit design is an approach best relegated to producing low-cost, physically manageable multichannel amplifiers—where one might accept some compromise in sound quality for the sake of squeezing five, six, or seven 100 watt channels into one moderate-sized package for a budget home-theater installation."


Cyrill Hammer (Soulution)
"if you want to have your product performing at the cutting edge it is not possible with today’s known switching technologies. In order to come close to the performance of the best linear design we would need high-current semiconductors that provide switching frequencies of several MHz or even GHz."

And there are quite a few more, if you want me to keep going?

Cheers George
More to discover