plinth for tts8000


in my quest to do a multiple tonearm for my tts Sony 

the original is mdf. and honestly sound a little dark and dead so.. my thoughts of cld type of strategy is 

top bamboo wood by ikea. 
middle rose wood
bottom 5mm of Alum since I need something to bolt on.

Any thoughts or suggestions welcomed 


anthonya
The Link will take you to a TTS 8000 Thread.
The TTS 8000 in question is one of two owned by the Lenco OP.
Similar to my own situation.
I have commissioned a rebuild of a Bearing with Modern Materials for one of my TTS's from a Engineer known for there workmanship with TT's . 
The OP is now having their TTS done in a similar manner from the same Engineer, they are nearly ready to receive their TTS with the New Materials in use.
I have too many TT's so asked for the OP's TTS to be Prioritised over my own one.

The A/B reports should be good to receive, as both the TTS's have Panzerholz Plinths,  and can use the same Rack/Support Set Up,
along with the same Tonearm > Cartridge.
The only obvious difference will be that one Plinth is of a very high standard of finish with the added veneer. 

There might be something stimulating in the Exotic Veneered Plinth to inspire the OP of this thread.

  

https://www.lencoheaven.net/forum/index.php?topic=33328.30
@lewm & @rauliruegas

I know both of you are very knowledgeable about TT’s in general. However After doing a lot of testing with various footer materials, there are materials like glass, Metals & Stone which raise red flags to me. IF you need to gain High freq. clarity those are among the best. I’ve never needed in, in my system and have fought brightness in my system. So I can’t imagine a plinth made out of either material (Though VPI sandwiched Alum in the Scoutmaster I had). I suppose either material can be damped and if so, fine. But a full on slate? Though it is a soft porous, does it need damping? I respect your experience do you believe it worked for you because your system needed the extra clarity? Just curious. Not meant as flames.

EDIT After re-reading the OP I notice he said the MDF Plinth was dark and dead. I understand that and maybe the hard metal or stone is in order. A tone wood may also be in order from my experience. I would still be interested in Lew & Raul"s answer to my question because my experience has been limited to my own system. 
Mass does nothing to isolate a turntable from environmental rumble. Not concrete floors or granite tops or heavy plinths. The only way to isolate a turntable from the environment is a stable suspension tuned to less than 3 Hz. Such a suspension isolates the turntable from everything above 3 Hz. Anyone can make a solid plinth look good. The trick is to make a suspended one look good. Avid does a good job as does Basis. The SME's are sort of industrial but very impressive in person. The Dohmann is an acquired taste. The Sota more or less classic. 
Lewm has done a lot of work with slate and drilling holes in slate is not easy. It chips very easily. One could make a suspended slate turntable.
You can suspend anything.
Put a seismometer app on your phone. Light up the app and place your phone on a table. Tap the table lightly with a finger and you will see the needle twitch. Right now I have my phone on the desk. I see every key stroke on the phone. The desk is on a concrete floor. I bang the floor with a foot and it registers on the phone. I just opened and closed the door to the office and that registered on the phone. The lightest tap of a finger registers on the phone. You think your rack is solid? Check it out with this phone app. You are in for a big surprise. Put the phone on your platter and start tapping around. Can you jump up and down in front of the turntable without it registering? What happens when your refrigerator compressor starts up or the washing machine.
Dear @artemus_5  :  I have not personal experiences in specific the use of slate in that application but I rememberd that lewm has it and with success.

R.
  MDF is never the best choice for a TT plinth.

True!!!

But the Well tempered turntable sounded good!