Audiophile-grade ground rod?

Best bet is plug your stereo into the wall and enjoy the music.

@lowrider57
Thanks for the Fremer link which describes the solution to his major audio quality degradation after installing an external electrical generator for power outages. Learning a lot of useful info.

You want a low impedance path to ground and that isn’t easy to achieve. I’ve wondered how you can get around this. Multiple grounding rods should help.

Make sure that if using multiple rods, the scheme should be designed a single point ground - which IIRC the rods are connected in series vs parallel, otherwise the noise will be going from one rod back into another rod and a lightning strike may create an EMF impulse to fry your electronics.

Additional electrical and grounding rod info:
https://audiobacon.net/2019/12/14/how-to-wire-your-home-for-hi-fi-tips-tricks/

Project ground for billionaire audiophile.
The Earth's core is thought to be iron.  Iron is a pretty good conductor.
All that is necessary to reach it is a ground rod about 3000 miles long (and a big hammer).  This will be an excellent ground but will probably melt because of the high temperature down there.  So you will have to keep on hammering.

Perhaps more practical...
1.  In another topic I suggested a separate earth for audio system circuits to remove earth loops with other circuits powering noisy equipment

2.   If ground is dry around your ground rod, water it every few days or install a drip feed.

as noted, dirt is not a great conductor, so will likely take several grounding rods to lower the resistance measurement significantly. 

@tonywinga ,

I was hoping you would respond to my above post in response to yours.

My post, 10/21/2021 9:03am.

It’s not often to read a post where someone with your back ground, can backup their findings with actual hands on testing with measurements.
I don’t doubt for a second what your test engineer suggested driving the ground solved the problem you were having. But do you know for sure why it did?

1) How old is the building? The reason I ask as a building ages the soil under a concrete slab, floor, that is on poured on grade will dry out.
2) What is the length of the ground rod that is driven into the earth through the drilled hole in the concrete floor? 8ft? Less?

3) By chance was the rod to soil resistivity, resistance, checked using the proper type of test equipment? If tested what did it measure? Less than 5 ohms?
If not tested the rod to soil resistance could actually be high. If the resistance is high then basically it would be no different than floating the chassis of the piece of test equipment above ground. Or at the very least equal to a resistor, resistance, in series with the test equipment and earth connection...By chance did the test engineer repeat the same test with the ground rod ground wire lifted from the piece of test equipment? (Floating the test equipment chassis above ground.)

4) If the test equipment is made to be used on airplanes I can’t help but wonder why you are not using a medical grade type Isolation transformer for a power source for the testing equipment.

One thing I have learned over the years about branch circuit wiring is the type of wiring used and the wiring method used for installation can make a difference on how well a circuit will perform.

A true dedicated circuit should not share the same raceway, conduit, or cable assembly with other branch circuits. Installing more than one branch circuit in the same conduit can/will cause induced voltage, as well as noise, from one current carrying circuit conductors to the other. Also when an insulated EGC is pulled in the conduit the current carrying circuit conductors can induce a voltage, and noise, onto the insulated EGC. This is true even for a dedicated circuit installed in a dedicated conduit where the hot, neutral, and insulated EGC are installed loosely, randomly, in the conduit. Twisting the current carrying conductors together and installing the EGC just along side the twisted current carrying conductors in the conduit greatly reduces the induced voltage onto the EGC.

Well worth reading.
2012 Seminar w-Notes v1-0.ppt - indy-aes-2012-seminar-w-notes-v1-0.pdf

Note page 16 and read pages 31 thru 36.

/ / / / /

FWIW: A test of a dedicated ground rod not bonded, connected, to the electrical service main system ground. (Grounding Electrode System).

A while back I drove a 5/8" x 8’ ground rod in the rock garden at the back of the house to use as a dedicated test grounding electrode. The driven ground rod is probably a good 70’ straight as the crow fly s, from the electrical service’s three 10’ each driven ground rods. I did a quick check measurement today and the difference of potential, voltage, from the test ground rod to the electrical service grounding electrode system measured 347mV. ( Meter, Fluke 87 mulimeter).

.