DIY high end speakers?


Is there any consensus on which of the published (via Internet) speaker designs / kits are actually worth it? I am very handy (I design and build furniture as a hobby and have a full shop) and as a result am considering going the DIY route for speakers but I need a starting point for my research.

What are some good links and resources for me to check out and see if this is a good way to go?

Thx
kooshballa
While I built and own a set of Linkwitz Orions and am rebuilding nicer cabinets in the Orion-4 style with solid lumber curly maple baffles, Gabon ebony trim, and zebra wood sides (they will be _much_ prettier than any of the following designs) I'd also recommend looking at

- The NaO Note. The polar radiation is more uniform than Orion (which has broadening dispersion crossing from the midrange drivers to tweeters that is compensated for in Orion 3.1+ with the shelving low pass filter), it should sound even more natural, and it costs less. I have not heard them and hope some one brings a pair to Burning Amp 2012.

- The Gedlee speakers. While flat packs and not the same degree of DIY they're the only speakers more than a couple Orion owners have preferred. I haven't heard them specifically, although I have heard other wave guides paired to large mid-woofers with matching directivity at the cross-over point which produces exceptionally natural sounding results with silly headroom without the cost of the driver displacement which goes with dipole mid-bass. Earl's competence should produce very similar (but perhaps better) results.

For lower output levels than I prefer for acoustic music Pluto works great and makes more sense (sounds more natural) than any box speaker with the same driver sizes, although the small mid-bass limits its headroom (Pluto 2 does 6dB better which may be enough for you). Pluto+ addresses that and provides last octave extension, but by that time your parts cost is getting closer to the other speakers (my Pluto+ build probably ran 75% of what I spent on the Orions; although that was before the dollar got weak and Scandinavian drivers got so expensive). I built/own Pluto+ too.

I'd avoid nearly all conventional box designs since the directivity mismatch between the mid-range and dome tweeter puts a 2-4KHz peak in the first reflections' spectra which sounds unnatural and makes them more sensitive to placement than better behaved speakers like the above.
I have heard a number of DIY designs (and built about 15 or some from
various speaker designers.) I'm a cabinet builder not a crossover guy, so I've
looked for work by people who I consider to be very talented.

I have not heard the Linkwtiz kit, and I am sure it is very good. But to say
anything is without peer I think is a mistake. There tons and tons of DIY
designs out there be people that really know what they are doing, no one has
heard them all.

Madisound is a fun place to start. (http://www.madisound.com. They
have kits they have designed, they also have kits by popular designers. In
addition, they can measure and build any type of speaker you want.

Meniscus audio has a similar philosophy. (http://www.meniscusaudio.com)
They also do custom work, but actually measure drivers in cabinets. In
addition, they have tons of kits for basically every driver they sell. Good folks
over there.

There are message boards with shared designs. At
http://www.htguide.com/forum
you will find the statement series from Curt Campbell. Many people have
been highly impressed.

As Peter mentioned, Troels does incredible work with all types of drivers. So
does John Krutke of Zaph audio (http://www.zaphaudio.com). I
helped a friend build the ZRT 2.5. A super nice design for a pretty minimal
outlay of cash compared to the finished speakers available at that price.

Tony Gee at http://www.humblehomemadehifi.com is no longer publishing
free designs, but his archive page still
has probably close to 30 designs.

I know there are people that say DIY designs will never rival the commercial
competition. But a lot of the stuff I listed above is beyond what I could call
DIY. They have similar measurement and testing setups to a lot of
commercial speaker designers, and are able to spend more time tweaking
crossovers because they don't have to hit a price point and are not necessarily
concerned with number of hours spent on designs.

The parts express board has some more cost effective designs that are very
nice as well. (http://techtalk.parts-express.com) Have fun exploring. For
me, it's become an addition. I've had over 40 pairs of commercials speakers,
but I've come to the conclusion that because I'm competent with cabinet
building, veneer work, and finishing, I can't afford to buy commercial
speakers any more. The value (in general) isn't there for me. The most fun
for me has been learning the skill of unbacked veneering. I've spent countless
hours perfecting my abilities in that arena and really enjoy it.