2. analog
  3. 1218590901

Weird issue with my VPI... please help

I have a VPI Scoutmaster with a Shelter 501 MKII cartridge.

This is fairly new, so cartridge has maybe 40 hours on it.

Imagine a graphic EQ where you pushed the lowest band up full... and did the same to one other band in the upper midrange... and that's what it sounds like.

I thought it was something else in the playback chain, but I've isolated it to the turntable (switched phono stages to be sure). Other sources play fine so it's not the preamp or speakers etc.

Any ideas? I don't know if it's always been like this because when I first got the turntable I had some serious speaker issues where I couldn't hear the difference between any electronics (had a very muddy sound). Now that I have that cleared up (CDs sound great) I can hear the difference between different preamps etc... so I finally sit down to hear what my new vinyl collection actually sounds like... only to find out I have a problem of sorts.

The cartridge was setup by Elusivedisc.com where I bought the turntable.

Any help much appreciated!
madfloyd
stringreen's avatar
stringreen
6,470 posts
 
Madfloyd... The VPI Signature 9 incher works extremely well with Dynas and Benz's. The "signature" is mainly the use of Nordost tonearm wiring (there is additional tonearm tube damping). I must admit it doesn't sound very good at all when new. My tonearm (or cartridge - but I suspect it was the tonearm Nordost) took hundreds of hours to break in. Be patient though, the rewards are great. A light bulb just went off as I wrote this. There are those that really badmouth VPI arms. I'm just wondering if they heard one that wasn't yet broken in... just wondering.
Those people who are Anti-VPI tonearm people might also check out www.high-endaudio.com/RC-tonearm.html Here is a listing of tonearms that rank the VPI 10.5i in the same category as Graham and Triplanar. Don't believe everything in print..especially on the internet, however, it is interesting.
Ag insider logo xs@2x
islandmandan
1,260 posts
 
Dynavector does work very well in the signature arm. Not bright, but well balanced (amazing with those high-rez 45 lp's). You might consider getting another cartridge, something fairly inexpensive yet good, to see if that takes care of the problem. It's good to have a spare cartridge around, too. I happen to have Fremer's set-up disc, and I'm through with it now. Send me an email, and we can probably work something out, if you like. Best of luck, Dan
artemus_5's avatar
artemus_5
1,965 posts
 
Madfloyd. I upgraded to the Signature arm and never looked back. It was a very good upgrade which I would recommend. My room is an untreated living Room. If I have any problem with it, it would be its slight tendency towards brightness on some albums. I have noticed no undue brightness with the Sig arm. Tighter bass and more detail is what I heard. There is no more tendency towards brightness with the Sig arm than the standard arm. I have used a Dyna 20XL and a Benz Ebony L with great success.
As someone else has said, your problem is not the arm/cart match. I suspect a bad cartridge.
madfloyd OP
411 posts
 
Artemus,

If I'm not mistaken, the Dyna 20 is $700 and the Benz Ebony L is $3500?

What are the sonic differences between the two? Which do you use now?

Received my (Michael Fremer) setup DVD and Analog test LP so hopefully I can learn a bit over the next few days and rule out poor setup, but at this point I'm figuring it's either the cartridge or just the sound of VPI.

I've played some more LPs over the past few days and it doesn't sound so much out of phase as a total lack of midbass and midrange, very thin highs. I'm now worried because I've been getting some private emails suggesting I may just not like the VPI sound.
narrod
1,064 posts
 
It's not the sound of VPI. Look elsewhere.
More to discover