TT Weights VPI center clamp


I was jus wondering, does the TT Weights VPI screw down clamp damage th record label in any way when it is tightened?

The original VPI clamps outer part does not move when tightened. only the center screw part moves so the label is not damaged. Other after market clamps for VPI seem to also use this method, and for the same reason.

The TT Weights clamps look real nice, but I am worried about label damage when using them. Can anyone with real experience please chime in?
ptmconsulting
I use TTWeights top of the line VPI center weight. This one does not screw on. It is stainless steel and has a silky-smooth damping material on the bottom. You do not use the VPI rubber washer with it. I like it much more than both of the VPI screw-down clamps I have (stainless steel/ delrin, delrin). Some people may think that a cupped LP sounds better though that seems counter-intuitive to me. The TTWeights gets kudos from me also for ease of use and build quality. It is very pleasing to the eye and ear. No affiliation with TT Weights- just a happy repeat customer.
I use the VPI ring clamp. In e-mails with VPI and Elusive Disc, both indicated the ring clamp does the job of holding the LP down and flat. A spindle "device" can then be used for resonance control, but does not necessarily need to "clamp" the LP down or add additional weight. Doesn't mean you can't use a "weighted" or "clamping" spindle device, though.

On there recommendations, I chose to use the VPI ring clamp with the BDR The Clamp. Very pleased.
I had forgotten, that such a topic, like all other audio topics can have as many opinions as there are posters.

Should the moderators permit, this could probably be a thread that could numbers into the dozens of posts.

Most feel the benefit of a clamp to be resonance control. Even Harry W himself no doubt believed this was the sole benefit. But of course there are others.

I know many here work very hard to achieve proper set-up of Table-Arm-Cartridge, and we can talk about things like Overhang, Azimuth, Zenith Angle all day long.

To me, it doesn't make much logical sense after all this hard work, and now you're placing an LP that looks like a Taco, or becomes Taco'd after improper precise clamping of an LP to Platter. Not to mention th extra work a Stylus-Cantilever has to do following a warped LP, and the detriment to good sound because of it.

The beauty of a Screw Down Clamp with Tables that posess the VPIS design, is variance of Clamping Force is easily obtained. With a weight, there's no adjustablity. The screw Clamp can be just barely applied, or provide much more clamping force than any weight can apply.

If one seeks the additional Mass, then buy the heaviest weight available.

All VPI Platters have been specially designed to work hand in hand with a Clamp that adheres to VPI's Clamp Design.
The use of the Rubber Washer was cheap, but effective, and smart.

Why TT Weights chose to veer from the VPI Design, and not at least provide a comparably designed product is unknown to me? I'm sure they have the expertise to make a beautiful two-piece clamp with adherence to the VPI Design had they chosen to.

I know many will comment about the sonic improvements, or lack of, with different Clamp Designs. I'm as well concerned that the Clamp-weight does it's intended job, and prefer the limitless range of adjustability/clamping force that a screw type design has.

I feel it does little good to be looking at a gorgeous Clamp, yet the LP looks like a Frisbee while in play.
While the azimuth error variance may be small, I would assume it is still there.

I myself chose a custom machined Screw Type Clamp made by a local machinist, but it does precisely adhere to the VPI Design. Mark
A two-piece screw clamp (as Markd51 described and as Teres clamps are) makes it easy to avoid label damage. Just stop the clamping piece from spinning while you tighten. One-piece screw clamps don't allow that, so *may* risk some label damage.

If a clamp uses rubber or a similar material at the interface between clamp and LP it may have a negative impact on sonics. Rubber absorbs vibrational energies, shifts them in amplitude and frequency, then releases them after a time delay. This softens transients, dulls dynamics and smothers low level details. In a word: mud.

If you can, try removing the rubber bit and using the clamp "bareback". Your system resolution will probably increase. Everything should tighten up a little. If maximum resolution is your goal, remove rubber from around your analog rig wherever you can.
Assuming the OP’s question was legitimate, I can honestly state that the screw down design DOES NOT damage the label (or anything else for that matter) in any way. Remember we are talking about screwing it down by hand...

I’ve been using their Brass 1080g weight for several years on my VPI Aries (original) without any problems.