Although VPI has discontinued production of the HW-19 Series, they still do carry some of the parts needed to do upgrades to the Table.
They sell what they call a MK-IV Plinth, which is sort of similar to the originally made MK-IV Plinth, but is now only a one piece sheet of 1/2" Black Acrylic, with a Steel Sub Chassis Plate. Price I believe is $300 shipped for it, and I'm quite certain that VPI will gladly pre-drill the Plinth Sheet for an Arm of Choice.
If they would possibly not have the specs on hand for any given choice of Tonearm, then all they would simply need is the Arm Mounting Template, and Tonearm Base Specs.
The only possible downside to this one piece Plinth, is if using a very thick Platter, rather than the thinner Junior Platter, one might have to have a Tonearm Mounting Base Spacer made to lift the Arm higher for better.correct adjustability of VTA height of the Arm.
Just about every Platter VPI ever made, past and present will fit the HW-19 Series, with the exception of the now gone Super Platter that was specifically designed for the Flagship HR-X Table.
AudioPoints, and others make direct replacement thread in 10/32 Brass Cone Point Feet, and Coupling Discs, that not only improve sonics to quite an extent, but also vastly improve the look of the Table as well.
The SAMA (Stand Alone Motor Assembly is still available, but improvements-tweaks can be made within the HW-19, to better isolate the original 600rpm Hurst Motor and its Bracketry.
The SAMA is actually the exact same 600rpm Hurst Motor, but it is within its own Metal Case, and thus is seperated from the Table's Base.
The VPI SDS is as well another option, and can be used with every VPI Table ever made, as well as other Belt Drive Tables that use an AC Synchronous Drive Motor.
You have made no mention of what Tonearm is presently on your HW-19? If a Rega RB-300, I believe the Origin Live Silver will be a direct drop in fit. If Audioquest, and at 211mm S-P, the Jelco ST-250ST should be a direct drop in fit, and is a good Arm for the little money spent.
Sure, you could probably place a Graham Arm, TriPlanar, or other very costly Arm on the Table, but some might say it would be akin to placing a silk hat on a pig. None the less, a Tonearm contributes a lot to a Table's final sonics, the better the Arm, often the better the sound without a doubt.
There's many audiophiles here who change Cartridges almost like I change socks, and thus, one can often find a very nice low hour MC, or MM Cartridge with a good savings versus new.
Over the years, I have upgraded my own HW-19 Table, even though some parts were no longer made, almost all the parts came from right here, used from other members.
When the parts surfaced, that was when I bought them, and the Table, which was once a work in progress has been taken just about as far as it can go.
My Table is outstanding in it's performance, teamed with an AQ-9 Arm, MK-IV Platter, custom Clamp, ZYX Airy 3X Cartridge, and Sutherland PhD Phono Stage. With the custom Plinth, Brass feet, custom 1.00" Black Acrylic Plinth, it is also a stunning looking "classic".
I think it would take a lot of $$$$ Table/Arm to drastically outdo this one I have. Mark
They sell what they call a MK-IV Plinth, which is sort of similar to the originally made MK-IV Plinth, but is now only a one piece sheet of 1/2" Black Acrylic, with a Steel Sub Chassis Plate. Price I believe is $300 shipped for it, and I'm quite certain that VPI will gladly pre-drill the Plinth Sheet for an Arm of Choice.
If they would possibly not have the specs on hand for any given choice of Tonearm, then all they would simply need is the Arm Mounting Template, and Tonearm Base Specs.
The only possible downside to this one piece Plinth, is if using a very thick Platter, rather than the thinner Junior Platter, one might have to have a Tonearm Mounting Base Spacer made to lift the Arm higher for better.correct adjustability of VTA height of the Arm.
Just about every Platter VPI ever made, past and present will fit the HW-19 Series, with the exception of the now gone Super Platter that was specifically designed for the Flagship HR-X Table.
AudioPoints, and others make direct replacement thread in 10/32 Brass Cone Point Feet, and Coupling Discs, that not only improve sonics to quite an extent, but also vastly improve the look of the Table as well.
The SAMA (Stand Alone Motor Assembly is still available, but improvements-tweaks can be made within the HW-19, to better isolate the original 600rpm Hurst Motor and its Bracketry.
The SAMA is actually the exact same 600rpm Hurst Motor, but it is within its own Metal Case, and thus is seperated from the Table's Base.
The VPI SDS is as well another option, and can be used with every VPI Table ever made, as well as other Belt Drive Tables that use an AC Synchronous Drive Motor.
You have made no mention of what Tonearm is presently on your HW-19? If a Rega RB-300, I believe the Origin Live Silver will be a direct drop in fit. If Audioquest, and at 211mm S-P, the Jelco ST-250ST should be a direct drop in fit, and is a good Arm for the little money spent.
Sure, you could probably place a Graham Arm, TriPlanar, or other very costly Arm on the Table, but some might say it would be akin to placing a silk hat on a pig. None the less, a Tonearm contributes a lot to a Table's final sonics, the better the Arm, often the better the sound without a doubt.
There's many audiophiles here who change Cartridges almost like I change socks, and thus, one can often find a very nice low hour MC, or MM Cartridge with a good savings versus new.
Over the years, I have upgraded my own HW-19 Table, even though some parts were no longer made, almost all the parts came from right here, used from other members.
When the parts surfaced, that was when I bought them, and the Table, which was once a work in progress has been taken just about as far as it can go.
My Table is outstanding in it's performance, teamed with an AQ-9 Arm, MK-IV Platter, custom Clamp, ZYX Airy 3X Cartridge, and Sutherland PhD Phono Stage. With the custom Plinth, Brass feet, custom 1.00" Black Acrylic Plinth, it is also a stunning looking "classic".
I think it would take a lot of $$$$ Table/Arm to drastically outdo this one I have. Mark