2. cables
  3. 1256217831

Power Cables which take the soundstage back

Hello,
I have almost always focused on ICs and Spk Cables...but I always knew that Power chords also make a good difference. This is the first time I am venturing seriously into power chords. I am not looking for anything fancy. Primarily I see power chords should be doing the following:

a) Clean up the background noise (because of better shielding etc) which a stock chord would not be doing a good job at.

b) Provide good current capabilities which enables to make music denser, tones get more body and especially bass gets meatier and tighter (the last one normally happens more often)

These are primarily two things I am looking at.
I have tried some power chords in the near past and I have observed one common pattern:

1. Power chords which tighten up the bass (in comparison to stock chords) also bring the images a bit forward.

2. Some Power chords do a good job of taking the soundstage further back...I dont know how and why but I have seen it happening. Some of them end up presenting a bit loose bass in the process (only some of them)

So, for me at this point, a power chord which can take the soundstage back (without introducing anomalies like loose bass) would be a wonderful addition. Thats a very critical requirement for me. I am sure you guys would have experienced power chords which do such things. I am not intending to shell out more than $200 (new or used) at this point. Kindly suggest.
pani
beavis
272 posts
 
You may be better off installing dedicated line. But I agree with Macdadtexas. "Buy better upstream gear with your money, or better speakers." Or software.
stringreen's avatar
stringreen
6,471 posts
 
EVERY power cord changes my system...they all add, subtract, enlarge, reduce, etc., etc. I built my own with Accrolink wire and Oyeida plugs or Furutech. I have an all Ayre system with Vandersteen 5A's. The amp likes the Furutech plugs, whereas the speakers, the Universal player, and the preamp like the Oyeida. If I put Oyeida in the amp, and the Furutech in any of the other components, it doesn't sound as good. You must try each power cord in the position it will function to determine its efficacy.
hifitime
715 posts
 
The better the cord,I guess the more pure noise you will receive.Look at some of the power lines supplying residential areas.Some may be tied to industrial equipment with a lot more noise. The manufactures dislike the blind ABX test.Less profit?Maybe a line conditioner will do more good?There are
some power cords that have such bad solder jobs on their plugs,its unreal!Also,what is it going to take to make this right? A home burning down,taking lives with it over a mega buck
profit greedy company going to court to face the results their actions!A $20 cord will bring you all the dirty power you need!A link on the subject.link >>>[http://www.hometheaterhifi.com/volume_11_4/feature-article-blind-test-power-cords-12-2004.html]
richard_stacy
686 posts
 
this is a bit off topic from the op's request but it does support your thoughts to explore power cables. it is hard to quantify but i would confidently say that with power cable additions alone, i have increased the quality/performance of my system by 30%-40%. i admittedly invested more than you are looking to but it is relative to the overall system investment. i agree with much of what stringreen wrote in that it takes some playing around with different designs to get to a good place. some cables don't sound right on one piece of gear but fit perfect on another. i have 3 different brands of power cords but each seem to be the right fit for the gear they feed, it was a project to get to this point.

it amazes me to read so many posts stating they cannot hear a difference with upgraded cords. it is truly night and day in my system. i do not understand the philosophy of upgrading a component vs adding a power cable. if you like the piece of gear, it makes sense to do all you can to allow it to perform to it's full potential. most manufacturer's expect us to toss the cord that comes with it and attach one designed for audiophile performance.

good luck on your quest...
jiminlogansquare
13 posts
 
I'll chime in here as a recent convert (but not zealot) in the "power cords make a difference to the sound" camp. Over the past two months, I have gone from using all stock power cords and a Home Depot surge protector to:

PS Audio Perfect Wave AC-12 from the outlet to a PS Audio Quintet

PS Audio Perfect Wave AC-5s from the Quintet to (1) my amp (Cambridge 840A v.2) and (2) my front end (Olive Opus No.4, with digital out to a DAC Magic).

Yes, these changes improved the sound of my system. Less noise, bigger (and TALLER) soundstage. It has not been subtle.

But surprisingly, the biggest difference came when I added the AC-5 to the Olive Opus. This one sealed the deal for me; the things are expensive, unwieldy, and like electric garden hoses, but they DO make a difference, especially (in my case) when hooked up to the digital equipment.
More to discover