Is Bi - amping worth the trouble?


Hello all...

I'm on the fence with the thought of bi amping. A big part of me wants to go ahead with it... the 'wallet' part says "Not so fast".

There should be lots of folks who've biamped speakers before... When it was all said and done, "Was it worth the time and expense?"

I'm inclinded to add a tube amp for the upper end of my VR4 JR's ... or any other speakers for that matter... though in any case and reardless the speakers, tube amp on top, and SS on the bottom.

...and then there's the thought of keeping two dissimilarly powered amps matched at the same volume level... and the added IC's, PC, and stand... it does seem to add up.

... and at this point, I'm thinking BAT to keep things all the same... and am not sure there, wether even that matters too much...

I sure do appreciate the input.
blindjim
Blindjim: -3dB is equivalent to a loss of 50% of the signal, which would not only alter the amplitude, but also the quality of the signal in most cases. I'm not trying to pick on you, but i find that figure to be way out of line to say the least. If someone were to latch onto that figure and use it as a point of reference, it may end up skewing their results or calculations. As such, i questioned this for sake of clarity as others may refer to this thread as point of reference in the Agon archives.

My own experience dictates a loss of appr .1 dB for a good quality connection that maintains similar mating impedances. The more that the mating impedances differ from one another, and the poorer the surface contact between them, the higher the losses involved. From my experience, a 50% drop ( -3dB ) in signal would require one helluva bad connection ( limited clean contact area ) between drastically different mating impedances. Sean
>

Gain or loss of signal "strength" is measured in decibels, Do not confuse signal strength with sound pressure levels. there is more than one way to look at things. I was talking about the post alluding to signal degredation... how one could confuse signal loss or distortion and see it as sound pressure level indications, is beyond me.

Don't worry, Sean, You can't pick on me... especially if you and I are not talking about the same thing... and little of this aside has anything to do with the thrust of the notion as to wether or not bi amping is worth it I would think. Decibels are used to measure more than simple sound levels. Just a reminder for the more pedantic.

All I said, in my previous follow up, was I do not believe the addition of more amplifiers and the required peripherals will degrade the sound, or the signal to the extent that it is diffused or distorted. were that the case, ONLY the shortest path for the signal should ever be pursued. hence, with that sort of thinking, 'seperates' would not truly the best approach.... this is not the apparent case however as the largest majority of systems are comprised of separates.

So, it should stand to reason, the addition of more than one amp to develop a signal, should not, in and of itself, be seen as detraction from the bi amping path, or in any fashion provide an inheirent issue for signal improprieities. there's bigger fish to fry with adding amps than the worry of signal loss.

Hope that helps.
Blindjim: Signal strength / drive levels and SPL's are directly correlated in an audio system, albeit at a non-linear rate. This has to do with losses through-out the chain, mostly within the speakers. Most all of these losses are easily measured ( or at least approximated ) if one has the know-how and proper test equipment.

Having said that, the figures that i quoted were pertaining to actual line level measurements, not spl measurements. Since your reply was of a generic nature, i'm not certain if you were responding to Gregm as an individual, myself as an individual or both of us simultaneously. Obviously, we can't discuss the same subject if the subject being discussed and responded to is not clear. There is no body language to be interpreted over the net and we can't read your mind as to who you are talking to or where a specific comment was aimed at. As such, it helps to segment or identify who / what a specific reply is aimed at.

I don't think that anyone responding to your last few comments was being pedantic, so much as trying to figure out how and where you arrived at the figures that you proclaimed to be accurate. I'll have to assume that you avoided clarifying the issue for specific reasons and let it go.

Other than that, i hope that this thread has given you some insight as to the many variables involved. Given your last response, it would appear that you're now answering your own questions, so i guess we're done here. Toodles.... Sean
>
Why don't you just bi-wire?? It's easier and well worth the effort. Use Anati-Cables - very cheap and excellent.
Sean.
"We are done here" ??

I was done some time ago. In fact, I believe anything of note was entered way back and certainly before your posts to the thread. I am relieved however, that you have taken it upon yourself to culminate things so cavileir like, though...

it's a sure bet you can not read minds. had you been able to you would have realized my choice of words was not pointed at yourself. Merely a generic and I thought, somewhat humorous ment regarding the more nit pickyish of us. If you feel it pertains to yourself, then, perhaps it does... though it was unintentionally and ambiguously aimed, and truth be told, of all the Audio nuts out there, (myself included), it is apt in any case.

You take things to much to heart Sean... get some thicker skin, friend. I bear you no ill will. Reading my follow up I thought would have been explanation enough... Whomever it was that asked about the SPL meter I used... THAT was to whom I was relating. I saw no need to clarify further, I should have. My PC wasn’t reading the page properly. I’ll be more careful next time. It’s not my desire to be consciously injurious.