Lightspeed Attenuator - Best Preamp Ever?


The question is a bit rhetorical. No preamp is the best ever, and much depends on system context. I am starting this thread beacuase there is a lot of info on this preamp in a Music First Audio Passive...thread, an Slagle AVC Modules...thread and wanted to be sure that information on this amazing product did not get lost in those threads.

I suspect that many folks may give this preamp a try at $450, direct from Australia, so I thought it would be good for current owners and future owners to have a place to describe their experience with this preamp.

It is a passive preamp that uses light LEDs, rather than mechanical contacts, to alter resistance and thereby attenuation of the source signal. It has been extremely hot in the DIY community, since the maker of this preamp provided gernerously provided information on how to make one. The trick is that while there are few parts, getting it done right, the matching of the parts is time consuming and tricky, and to boot, most of use would solder our fingers together if we tried. At $450, don't bother. It is cased in a small chassis that is fully shielded alloy, it gets it's RF sink earth via the interconnects. Vibration doesn't come into it as there is nothing to get vibrated as it's passive, even the active led's are immune as they are gas element, no filaments. The feet I attach are soft silicon/sorbethane compound anyway just in case.

This is not audio jewelry with bling, but solidly made and there is little room (if any) for audionervosa or tweaking.

So is this the best preamp ever? It might be if you have a single source (though you could use a switch box), your source is 2v or higher, your IC from pre-amp to amp is less than 2m to keep capaitance low, your amp is 5kohm input or higher (most any tube amp), and your amp is relatively sensitive (1v input sensitivity or lower v would be just right). In other words, within a passive friendly system (you do have to give this some thought), this is the finest passive preamp I have ever heard, and I have has many ranging form resistor-based to TVCs and AVCs.

In my system, with my equipment, I think it is the best I have heard passive or active, but I lean towards prefering preamp neutrality and transparency, without loosing musicality, dynamics, or the handling of low bass and highs.

If you own one, what are your impressions versus anything you have heard?

Is it the best ever? I suspect for some it may be, and to say that for a $450 product makes it stupidgood.
pubul57
89db Merlins, .8v sensitivity amp, 2v source - 12 normal 3 as loud as I would ever want.
Similar to Pubul57 except my speakers are rated 92 dB (closer to 95 dB in reality) and I get between 1 and 3 o'clock.
My amp is 1.3V sensitive. After I get my 2V DAC, the only other change I will make will be to use 1/2 meter pair of solid core interconnects leaving the LSA to go to the amp (I'm in the process of cutting a one meter pair to half them). So, as George said, I can use RCA attenuators to cut the gain down a bit but I really don't want to add anything else in the path. I'm more of a "less is more" mindset. Anyone have experience with these devices degrading sound quality? I've come so far, I don't want to start going backwards...
I never liked those Rothwell attenuators. You can accomplish the same thing by adding a resistor in series with your interconnects (there might be a little more to it, but this is the basic idea). I believe Luminous Audio makes cables like this upon request. Since you are cutting up some cables now might be a good time to consider doing it.
The Rothwell attenuators work just like the Lightspeed Attenuator. That is, they have a soldered fixed series resistor with another shunt fixed resistor to ground, this forms a voltage divider just like the Lightspeed Attenuator.
Except the in the Lightspeed Attenuator these series and shunt resistors have variable resistance with the amount of light that shines on them. So what you have is a variable voltage divider in the Lightspeed Attenuator.
The only problem with the Rothwell's is that they change the input impedance of the device they are attached to, so this needs to be taken into consideration when using them, with passives and tube preamps.

Cheers George