After market Motor + Belt drive for Verdier


I have been looking to upgrade my TT motor and belt drive for some time now. I use a Nouvelle Verdier and its only sore point is its motor and silk thread drive. It is not bad, it gets the job done. The sound is neat and in general non-offensive. However, when I used a 0.25 inch magnetic tape (reel to reel) to drive the platter the overall sound became more dynamic, voices sounded younger, instruments sounded happier. It was as if the pitch of all the instruments became more realistic. But then I also heard more of the irregularities of the motor rotation, the timing of instruments messed up a little. The background was no more as clean as the thread drive.

This told me two things:
1. Silk thread is good but it affects music in a way that makes the performance a bit sleepy.

2. The stock motor is not good enough to accommodate a tighter coupling with the platter.

So, I am now looking for after market motor and belt drive solution. I looked at Teres motor but for that to work they require a sensor to be placed under the platter but my TT doesnt have enough gap between the platter and plinth to place the sensor. I am looking for some viable suggestions here.

A friend of mine suggested me to consider a flywheel between the motor and the platter which will absorb the motor irregularities. I dont know if it is worth a try because I see many good TTs do not have a flywheel, that means a good motor is all I need I guess but I am open to the flywheel idea also.
pani
Hi Ct0517,
I have not yet done the Teflon washer thing, I am not too handy with DIY and when I see wires running inside the motor housing I get nervous.

I use a Naim ARO tonearm with Miyabi Red Rose (Standard) cartridge and RCM Sensor Prelude phonostage. I listen mostly to Blues, Rock and Swing Jazz, so PRAT and tone are very important for me.

BTW, I forgot to answer your earlier question, you could stick the reel tapes with the use of Super Glue (instant glue).
I use a Naim ARO tonearm with Miyabi Red Rose (Standard) cartridge and RCM Sensor Prelude phonostage

Pani - fyi - this is just coincidence. Dover's last post on the ET2 thread. He uses a Final Audio string drive.

"The sound of the Naim Aro is quick, lucid through the mids, excellent soundstage and very musical. The downside is that I believe it has a very narrow operating window in terms of cartridge compliance and mass. The Dynavector Nova 13D sounds excellent as does a Denon 103D. The Koetsu Black sounds awful, unstable in the bottom end."

Hi Dover - if you happen to see this and can add anything?

Pani

if its the same inside like the Platine motor, the hardest thing about putting the teflon washers in is not losing the little aluminum washers that are there when you lift it out. The only wire you disconnect from what I remember is the ground. The washers cost one dollar.

Cheers
Hi Pani

Thanks for clearing up the tape and capstan drive.

Agree that music on R2R master tapes is THE reference for many , I am lucky to have tapes and a couple of Studers.
As good as vinyl gets it isn't in the same league as R2R.
Had a Nakamichi 582Z, yes they were good but no match for R2R.
There is so much vinyl that we cannot get on tape therefore I/we keep tuning the Verdier.

I like what CT0517 said about cars and tuning.
Cars are build for a broad group of individuals.
Those that like cars buy better cars that have a higher potential to be tuned to an individuals taste and abilities.
Tuning the Verdier is like a high performance car.
Easy to tune and it will reveal whats in the music.

Re the power supply.
Wouldn't want to spend too much on a battery powered box, but my old ASR was battery powered and my darTZeel pre is also battery powered....... I see a pattern here.
Will explore a battery power supply and will post my thoughts. An AGM battery and a simple charger should do.

Back to the R2R.
R2R is relatively inexpensive to get started but the tapes can get costly.
Friend in Seattle invited me to a gathering that took place at his place.

Here is my post from 04 13 2009 on Mike Lavigne's system page re R2R

http://forum.audiogon.com/cgi-bin/fr.pl?vaslt&1036349020&openusid&Rugyboogie&4&5&st1400

Take care and Viva le Verdier
Hi Ct0157, the Miyabi is a good match for the ARO. It is a proven combo actually. The ARO sounds good with Lyra and Dynavectors also. Koetsu, I dont know.

BTW, regarding the motor upgrade, Origin Live makes after market TT motors, possibly could be considered.

Where can I buy the Teflon washers from ?
Rugyboogie, thanks for your suggestions. I understand your view point and possibly I will do what it takes to make this guy sing the way I want. Some patience, some research and some funds are all that is required :)