Asymmetrical Room Treatment

The drapes will only dampen the very high frequencies at best. (20khz+)
Get some absorbers behind you and infront of the window.
I would also pull the bass trap out of the corner thats behind you.

You may not realize it because you don't have your first reflections dampened in the room. But trapping the rear corners will kill the soundstage of a room.
I would take the rear bass trap and put it in the same corner behind the right speaker with the other bass trap and that will kill any bass node that is behind your speakers.

The open wall to the left is allowing the bass to be dampened by escaping the room.

This will help in the bass department, but the imaging and soundstage will only be good with treatments in at least the first reflection points through out the room.
It's only then that you will be able to realize the potentual of your soundstage and imaging and ballance out the system.

My best freind has the same problem as you.
He's treated the room on the sides and behind his seating position and the soundstage is very ballanced.

Hope this helps.
John

Hi John. Thanks for the feedback! I actually do have hi/mid absorbers (foam, not 703) at my first reflection points on the side walls. I will move out the bass trap I have in the rear-right corner and place it with the others in the front behind the right speaker. This will mean I will have my 3 bass traps all in the front right, and the corners in the back will be untreated.

I have 2 additional foam absorbers along with the ones at the side-wall first reflection points, which I currently have against the front wall in the center and near the opening. Perhaps it would be good to use these against the back wall in front of the window? Or better yet, I guess I should probably just get another broadband absorber if not a diffusor, as suggested by Kevin, for back there. Good to know about drapes- I had assumed they would be effective a little further down, but I suppose it makes sense that they would only tame the very high frequencies...

Chisar, while the foam based devices/absorbers are not as "good", assuming they have a shaped face, you may find the following somewhat helpful for the wall behind you.

Glue a strip of very thin plywood (even just a veneer board) to the top of the foam's back. Get a suction cup clamp with hook (ie. Lowes, HD, Michaels) and stick this to the top of the window behind you. Since the foam is so light, even with the strip of wood, you can hang it directly on the window. Easy to remove when guests come over. I do this as my side window is a 1st reflection point and it is much more productive than just drapes (but not as good as a full fledged absorber).

While there is limited absorbption in doing so, assuming again that it has pyramids or something on its face, it will also act as a diffusor.

Another thing to consider for the open doorway is to use a tension based curtain/shower rod and install drapes in the doorway. With the right material and lots of folds in it even in the closed position, this will provide some support to what you are seeking to balance the two sides.

I recognize that there are better solutions, but based on limitations of renting, higher costs, etc. . . mine are only intended to offer easily changeable, relatively cheap and not to require drilling - as opposed to being the perfect solution that allows us to ignore these restrictions.

Hi Chris.
Putting some 4 inch absorbers in fromt of the window will definatly be a good choise.

They will act as bass traps and controle the mid and high reflections.

I found when you treat the rear corners of a room (behind the listening chair) it seems to kill the sound stage.
You must keep the rear corners lively and work on the first reflection points.

The foam you are useing is not doing much to absorb lower highs and lower.

The compressed fiberglass in the two inch size does a much better job.

Go to my system and read how to get the room treatment really cheap.

It's a do DIY set and you can do a room very well with minimum yen.

Hope this helps.
John

Hi Chris,

Thanks for your additional info. I have a different perspective and/or interpretation than one of the other replies so let me explain.

Back Wall Treatments: (1) A window on your back wall will act as the perfect bass trap – the long frequencies won’t even ‘see’ the window and will escape the room easily. So, I would redeploy your back wall bass traps elsewhere, not because it will damage the soundstage because that is more of a side wall reflections phenonmenum. (2) Drape absorbency is dependent upon the type and weight of material, degree of fold, and distance out from the wall. The heavier the fabric is the greater the absorption. From F. Alton Everest’s book, the absorption effect for velour drapes is concentrated in the 500-1KHz region using 18oz/yd2 material, but for 10-14oz/yd2 fabric is more within the 2kHz-4kHz range where the absorption coefficient tops out at 0.4 (40%). The deeper the folds within the drapes the greater the surface area for absorption – taking a drape pulled straight and then introducing folds deep enough that the drape is now only 50% as wide as it was when pulled straight increased the absorption coefficient from about 0.2 to 0.8 for 1kHz. A 1kHz wavelength is 13.6” long so placing the drapes at the 25% point of 13.6” means placing them out from the wall 3.4” to maximize the absorption effectiveness. I would suggest keeping your drapes or upgrading their density/thickness and creating deeper ‘folds’ in the material as you likely can’t move them farther away from the window/wall. (3) Making a diffuser for the back wall should be easy enough, but making it easily movable won’t be, so I’d stick with the thicker drapes for now. You can still place bass traps in the back wall corners from ceiling to floor should you decide to make or buy more.

Side Wall Treatments: (1) Your open-cell foam WILL absorb mid to higher frequencies depending on its thickness. A 2” Sonex foam with the anechoic-type wedges has an absorption coefficient of about 0.6 at 500Hz and the same coefficient at 250Hz when the thickness is doubled to 4”. The wedges look cool but actually reduce the absorption abilities due to the missing material in creating the wedges, and the surface isn’t hard enough to effectively diffuse frequencies. Your better off using OC701 or 703 material for increased absorption capabilities. (2) Soundstage width is a more a function of side wall reflections than back wall corner reflections. Back wall reflections create “listener envelopment” as per Toole in helping the trick the mind into thinking the room is larger than it is. Absorbing or diffusing/reflecting the side wall reflections, especially at the 1st reflection points, is a matter of taste, and the former will make the soundstage narrower with instruments as pinpoints in space whereas the latter will broaden the soundstage/apparent source width and size of instruments to being more life-like. In my latest incarnation of room treatments I’ve used planks of ¾” thick oak angled upwards to preserve the mid/high frequency energy so as to prevent over dampening the room and redirecting the reflections upwards to the RPG Skylines on my ceiling where they are diffused. It is also very effective at eliminating slap echoes between the two side walls.

Front Wall Treatment: If you were to put up a temporary hard surface in the doorway behind your left speaker, then that should keep some mid/high frequency energy in the room – the low frequencies will escape as it’s neither air tight nor thick enough. I think I’d be inclined to keep the opening as is and add broadband absorption to the middle and right side of the front wall to emulate the open doorway situation by the left speaker.

h
Having said all this, have you a SPL meter and test tones where you can get some rudimentary Freq VS SPL measurements to see how flat the frequency response is?

Good luck