Adding a sub woofer?


Running a Planar 6 to Icon Audio Ps1 Mk2 to Quicksilver Mid Monos into Klipsch RP8000F speakers. Want more low end, thinking of adding a sub. The mono blocks don't have a dedicated sub output so I was thinking about something like a PSB 250 which has both pre amp and speaker level inputs with speaker level outputs. A couple of questions.

What are the pros and cons of using the sub's preamp level inputs vs the speaker level inputs in this application?

And more importantly, right now my setup is pretty much tube analogue the whole way (and aside from the soft low end, I absolutely love the overall sound) - but does an inline sub like this do any processing, will it color the mids and highs in some way or is it just a clean pass-through in terms of sending the signal along to the speakers? 

Thanks for sharing your thoughts. 
Ryan
spotconlon
I own a pair of REL S2 SHO subwoofers.  What I like about them is their high level connection as well as their home theater connection for sound effects when watching movies.  I am glad I listened to the dealer because two rather than one.

Their high level connection allows the to ack more like woofers than subwoofers to extend the bass seamlessly.  The key is to make sure you set the volume so they don't stand out.  I set mine at 40% volume.  Otherwise, they sound boomy and they disguise the towers.  When you dial them in, they take some weight off the main speakers and allow the mid tones to play clearer.  Be curious to hear what volume level they se their REL's.

Be sure to not buy too small a size.  Buying too small will cause you to overplay the subwoofer and it becomes boomy.  I was going to go with a pair of REL T9's but decided to go with the S2 SHO's.  Glad I spent the extra money.
@ieales, absolutely. I think top model JL Audio subs may be the best available and their price reflects that. To my knowledge nobody makes a stand alone digital bass management system. The most sophisticated versions come with full room control units/preamplifiers. I must say however that the current units are easier to set up than the TacT units were. Almost any audiophile should be able to get decent results. The hardest part is setting up the microphone in the right place. The down side is the additional expense.
Having toiled with subwoofers since 1978 I can say unequivocally that you can not get the full benefit of subwoofers without a complete 2 way crossover,  be it analog or preferable digital. For those unfamiliar with this, the crossover goes between the preamplifier and the amplifiers. All connections are line level. Using speaker level connections drops the impedance to your amplifier decreasing it's damping. It is not acceptable.
Your money would be best spent upgrading your system before getting subs. 

As an REW alternative, the ML subs have an extra cost accessory called Perfect Bass Kit which includes Anthem Room Correction.

Pretty good results can be obtained with the PBK provided one does a bit of "book learnin'" with a room simulation application and a little common sense.
Hi Ryan,

Depending on how large your room is, what types of music you like to listen to and how loud you like to listen to it, a single PSB 250 or even two maybe too small.

What are the pros and cons of using the sub's preamp level inputs vs the speaker level inputs in this application?
 
In this case the pre level Inputs would allow you to use the PSB 250's low level input and output connection scheme that limits the level of the low frequencies reaching the mains. This setup would give you the most control and should be far easier to integrate than the other hookup methods.

does an inline sub like this do any processing, will it color the mids and highs in some way or is it just a clean pass-through in terms of sending the signal along to the speakers?

I did not read the owners manual all the way through but at the price point of the PSB 250 I highly doubt that there is any processing happening so it should be a clean pass through to your mains with the exception of the limiting of the level of the low frequencies below your chosen crossover frequency.

You may also need to plug the ports on the RP8000F's to get the best results. 

I noticed that the RP8000F's can be  Bi-amped. You may get satisfactory results with this option also if you can control the input gains of your amplifiers.