What happened to my room acoustics

I measured the spectrogram for my room at my MLP, and the FFT results are as follows:

- There is a roll-off before 20kHz.

- A dip is present around 12kHz.

- There is a noticeable boost between 50Hz and 1.5kHz.

- The bass rolls off around 33Hz at -3dB, consistent with the factory rating.

Comparing these measurements to the Burchardt measurements, there are some differences:

- It doesn’t exhibit a roll-off before 20kHz.

- The dip is around 15kHz.

- The boost between 50Hz and 1.5kHz is not as pronounced as in my room.

I’m curious about what might be happening with my room acoustics. If a fix is possible, what would it entail?

Spectrogram from my zoom


My room / speakers setup


Measurements from Burchardt


The room measures fine to me. Many are much worse. People just don’t measure and they have no idea. 

two things stood out to me.

#1 the seating distance

with the speakers 8’ apart my max seating distance would be 10’ and for me I would try closer to 8’ as it would maximize soundstage width at the cost of center focus (personal taste). Then I would toe in until the center focus is back. The down side of what I described is you shrink the sweet spot but you get a better sweet spot imo. 

Being so far away also pulls in a lot more room reflections. Closer will be more direct sound. 

#2 the equal distance from the side wall to back wall from the driver face should be avoided. This will increase the null created by the wave length that has a 1/4 wave of 3’. Which is right around 90hz. It will also result in a peak but I am not sure where that peak will be, but higher like 180hz for example. I would move them closer to the back wall (I know this sounds wrong but try it) to avoid equal distances.

the low end roll off is just using small speakers without correction, it is what it is.




First of all, your listening position need to be 5 feet closer. Things are actually worse then they seem. The Y axis is in 20 dB increments. Most systems I have seen use 5 dB increments. This is a very shouty curve with the bass lagging 10 to 15 dB behind the midrange. From 200 Hz up things are actually quite good except for that dip at 12KHz. You need to measure each channel separately and compare. 

The ideal in room curve starting at 20 Hz which should be 5 to 10 dB above baseline sloping down and reaching baseline at 100 to 120 Hz, then flat out to 1 kHz then a steady slope downwards to 6 to 12 dB under baseline at 20 kHz. Bothe channels should mirror each other directly. I would like to see if that 12 kHz dip is in both channels. Any difference between the two channels will screw up your imaging. 

You need to deaden the front and side walls at the first reflection point which may calm your midrange and I would remove the bass traps. After that your best option is a digital preamp with EQ and room control. Subwoofers and digital bass management would give you much more control over the bass. 

Don't feel bad. I have measured many systems worse than this. I just measured a system with Magico S7 loudspeakers. The imaging was pitiful for speakers of that caliber. Low and behold one channel had a 10 dB dip centered on 300 Hz. He is ordering a DEQX Pre 4 which will fix the problem. This is like a photograph out of focus. You use digital EQ to focus the system and you can see the results with your measurement system.  


Your room doesn't look that bad to me, many are much worse. Of interest is that you mapped out the "golden triangle" and then didn't adhere to it. As others have suggested, your listening chair is too far away from your speakers. I suggest you pull your speakers another foot into the room and move your seating position at least two feet farther into the room. Try listening to music instead of measurements.

A few comments:

Yes, move the seat forward. You’re probably hearing a lot from the rear wall you could eliminate by moving forward. My speakers are 8 feet apart and I sit 10 feet away. My back wall is another 9 feet behind me. Worth a try.

Did I miss comments about ceiling height? Some of the worst reflections come from floor or ceiling. They may be interfering. It's very helpful to measure impulse responses to see how the reflections are, or you won’t get a handle on imaging and soundstage.

Get those as many reflections between 4 and 12 ms down below -20db if you can. Viz.

measurement artifact - sweep length | Audio Science Review (ASR) Forum

- There is a roll-off before 20kHz.
- A dip is present around 12kHz.

COMMENT: These are very high and likely won’t matter much. (In my view.)
- There is a noticeable boost between 50Hz and 1.5kHz.

COMMENT: Much more important.