Good carts with SME V

Snacky - as a fellow Kiseki owner, I had the same issue with warped records.  I solved it by purchasing a couple of Vinyl Flat record flatteners.  An hour in the sun at 80 degrees F. and warped records come out pool table flat.  Great product, as is the NS Purpleheart.  My only other ‘issue’ with the Kiseki was the 80 hours it took to settle in.  Mine started out hot and required a lengthy break in before smoothing out.  

Thanks all. Yes, I am willing to listen - Koetsu, Kiseki, others.

Meanwhile here is a little home update, my Lyra Titan i.

Experimenting more with the Lyra Titan i, back in my SME V arm now that the Atlas is broken, I play Yes: Relayer, a kind of torture track test, known as very busy, dynamic record, not easy to get right.

I notice that adjustments (weight, antiskating, tonearm height) make a big difference. When they get better, what may at first sound like hardness and sibilants become less obtrusive. I had the arm quite high, turning it down ca parallel made for better mid-tone. Weight a bit up. Antiskating almost halfway down.

The Titan i does make this record sound “sharp”. But was it meant to sound that way? I think, yes. There should be some razor blade to the sound. Now that it is better adjusted, the bass performance is very tight and sounds great. The guitar of Steve Howe sounds more full, warm.

tkr - so the black could be the best Koetsu alternative in my context? Output 0.6 is fine. Which Urushi did you have? Just by looking I liked the sky blue. Not sure, which of the new more wider frequency (stone body?) Koetsus would be best match.
Oystein

I have tried the following Koetsus on my SME V: Black, Urushi Sky Blue and Coralstone. The Black was a very good match, the Urushi was a tad too romantic, and the Coralstone sounded, well, a bit disappointing. Right now, the Coralstone is mounted on my FR 64 FX, which IMO is a much better match for it than the SME V.
Mvh Tønnes

Dear @o_holter : "  But I love the Io’s rich sound and am willing to live with some tube noise.  ""

""  Bigger, bolder, better able to tackle dynamic music."""   

tube noise means higher distortion levels and that rich sound means " tubey ". Live MUSIC and what's in the recording and LP recorded grooves is way different to all those.

"" to polite the Cadenza Black.... ", not really problem is that you are accustomed to a " fake " sound, to much make-up when does not exist in the recording or live events.

As @nkonor I told you months ago that the weak audio item in your system is that IO: no matters what, period.

Again, forgeret rigth now for that cartridge/tonearm resonance frequency that has you: terroryze " when it's not exactly as you said.

Remember your Atlas thread where you insist on that resonance frequency issue that in reality you don't have it?.
In that thread my very first post was that because your Atlas had over 1,500 hours the problem belonged there and only at the ""  "" and after " thousands " of posts from other gentlemans you, by facts you experienced " was convinced that the problem was in the cartridge it self.

Now, you don't need to change your arm and if you like the Lyra signature then you can go with the Kleos that was the first Lyra design with the new  design characteristics where came the Atlas and Etna.
The Benz Micro is a great option too over the Koetsu and near to the Lyra.

But if I were you my focus will be in two subjects: a change in the phono stage and that Lyra fix your Atlas. No you don't need a different tonearm, your experiences with told all of us that the culprit was just from began the cartridge it self.

@lewm , it's almost ridiculous ( even that we all know it. ) to think that we will change the resonance frequency changing the counterweigth position and its weight. That's why almost never helps to change the resonance frequency say from 6hz to 8hz or from 12hz to 10hz.
The inertia moment is directly proportional to the distance of the weigth and that's why as far away from the fulcrum we change the weigth as higher or lower can be that resonance frequency value along a compliance that we can't really change.

Sometimes we want to invent the " black thread " when already " invented ".


Anyway, @o_holter  you already have the Atlas where I think no one can buy it from you so to fix it is the best way to go and in the mean time you have the Titan i and you can send the Clavis DC to Andy for retip with boron cantilever and I'm sure you will like it. Repeat, you don't need to change the SME 5.



R.