I'm looking to learn about Air Motion Transformer technology

Mike, Please excuse our old and outdated website. A new one with lots more info is in the works.

We use the Trinnov ST2 to control the AMT towers as well as the woofers. Our systems are designed with full DSP and room correction in mind. All filters and EQ is done by the DSP. The drivers are directly coupled to the amplifiers. The core is our AMT design and its ability to cover an extended range. Our 9 AMT driver Apollo tower can reach 80 Hz and below. Our 12 AMT driver Apollo tower just has more output. We have selected 120 Hz as the default crossover point for a variety of reasons. It can be easily changed through the DSP but we discourage it. Our woofers are designed to be stacked so room height is the limit. With their high sensitivity the Apollos can play to astonishing SPLs but no one should listen to those levels. Where their high SPLs count is with music peaks. Minimal dynamic compression.

Anytime you want to hear them just let us know.

And I would think Arion would know as he makes both types of speakers.
Having owned Apogee Divas I can relate to ribbons. His Analysis Audio speakers are strangely reminiscent of Apogee speakers. Mike, is there any connection to Apogee? I know, Apogee used a quasi ribbon woofer and it appears your speakers are using a design more like Magnepan. Ribbons are not just aluminum foil but aluminum foil traces laminated to a plastic. I think Apogee used very thin Kapton but I am not totally sure. The traces are connected in series which raises the impedance to somewhat reasonable levels. The impedance curve is extremely flat so in realty ribbons are a very easy load for an amp that can tolerate lower impedance's. Magnets run down both sides of the ribbon. A ribbon 6 feet long is very floppy so even though it is firmly connected at it's ends there are usually foam blocks placed at intervals to support the ribbon. You can not tension the ribbon too high or you will damage it. 
The Apogee bass ribbon was very easy to damage so I think the use of a planar magnetic design is smart. It is a much tougher driver. 

Thanx Mike I would love to. You wouldn't happen to have any dealers in New England?
Right now I use a TACT 2.2x for my front end which is more like The Trinnov Amethyst which is an ST2 with a few more inputs and a volume control. The room correction is identical. If my TACT were to fail that is what I would get at this moment in time.
I had a close relationship with Radomir Bozevic the DSP wizard behind  TACT. Do yourself a favor and do not sell anyone the microphone. Have your dealers set up the system, show the customer the basic stuff and remove the Mic. Boz got buried in phone calls. People were getting entirely lost in his program and coming up with inferior results which gave him a bad name aside from driving him crazy. His mistake was that he was direct purchase only and did not have any dealers to rescue the customer.
Anyway, stacking the woofers would be expensive. They would have to go all the way from the floor to the ceiling to create a line source that would go down to 20 Hz and match the output of the towers. You could take 4 subs and spread them across the front wall into the corners and achieve the same results. You have a horizontal line source! I do this with my ESLs with great results. No mater where you are the sound balance remains the same. Now my ESLs will not go as loud as your towers. Right now I use 4 12" subs. I would think 8 10" drivers would do the trick up to reasonable levels. To do  vertical line sources you would have to stack 6 or seven subs on each side? If you were to put them right into corners you might have output to match the towers which is academic really as nobody in their right mind would play it that loud.
Mike

There are no connections between Analysis and the now defunct Apogee brand. Analysis has been in business since about 1990. All Analysis M/T ribbons are designed with aluminum traces on a Kapton substrate. The main difference is the implementation. Most (all that I know of) ribbon membranes of the composite type are pleated through meaning the aluminum / Kapton composite are pleated together. Once done and suspended in the driver frame you basically have a spring. During assembly slight tension is applied mostly for symmetry. Over time they will sag. There are some negative consequences to that. Analysis ribbons are built differently. The Kapton substrate is not pleated. It is attached to the structure at the top and bottom with one to three cross-supports depending on which model and with slight tension. The pleated aluminum traces are applied to the substrate. Analysis ribbons never sag. There are several other benefits to the Analysis design. The Analysis bass panels are probably more like Magnepan panels but are, too, very different. They are also 3D in profile and have a complete suspension. Like most large ribbon or planar drivers they are an easy load on amps. Partially because of the design and the quality they are very stable and robust speakers unless you poke the membranes with sharp objects.

My car audio system uses AMT's ...I guess they're smaller to fit them all in the dashboard, kickpanels, etc.  There are good and not so good in all designs.