When the sound closes down then it is to much damping.When i had tonearms with damping trow i used as little fluid just so it touched the paddle.Hope this helps.
TONEARM DAMPING : DAMPED OR NOT ? ? USELESS ? ? WELCOMED ? ?
Dear friends: This tonearm critical subject sometimes can be controversial for say the least. Some audiophiles swear for non damped tonearms as the FR designs or SAEC or even the SME 3012 that is not very well damped in stock original status.
Some other audiophiles likes good damped tonearms.
In other thread a gentleman posted:
" If a cartridge is properly matched to the tonearm damping is not required. " and even explained all what we know about the ideal resonance frequency range between tonearm and cartridge ( 8hz to 12hz. ). He refered to this when said: " properly matched to the tonearm ".
In that same thread that a Triplanar tonearm owner posted:
" This is the one thing about the Triplanar that I don't like. I never use the damping trough...... I imagine someone might have a use for it; I removed the troughs on my Triplanars; its nice to imagine that it sounds better for doing so. "
At the other side here it's a very well damped tonearm:
https://audiotraveler.wordpress.com/tag/townshend/
Now, after the LP is in the spining TT platter ( everything the same, including well matched cartridge/tonearm. ) the must critical issue is what happens once the cartridge stylus tip hits/track the LP grooves modulations.
The ideal is that those groove modulations can pass to the cartridge motor with out any additional kind of developed resonances/vibrations and that the transducer makes its job mantaining the delicated and sensible signal integrity that comes in those recorded groove modulations.
That is the ideal and could be utopic because all over the process/trip of the cartridge signal between the stylus tip ride and the output at the tonearm cable the signal suffers degradation ( resonances/vibrations/feedback ) mainly developed through all that " long trip " .
So, DAMPING IS NEED IT AT THE TONEARM/HEADSHELL SIDE OR NOT?
I'm trying to find out the " true " about and not looking if what we like it or not like it is rigth or not but what should be about and why of that " should be ".
I invite all of you analog lovers audiophiles to share your points of view in this critical analog audio subject. WHAT DO YOU THINK ABOUT?
Thank's in advance.
Regards and enjoy the MUSIC NOT DISTORTIONS,
R.
Some other audiophiles likes good damped tonearms.
In other thread a gentleman posted:
" If a cartridge is properly matched to the tonearm damping is not required. " and even explained all what we know about the ideal resonance frequency range between tonearm and cartridge ( 8hz to 12hz. ). He refered to this when said: " properly matched to the tonearm ".
In that same thread that a Triplanar tonearm owner posted:
" This is the one thing about the Triplanar that I don't like. I never use the damping trough...... I imagine someone might have a use for it; I removed the troughs on my Triplanars; its nice to imagine that it sounds better for doing so. "
At the other side here it's a very well damped tonearm:
https://audiotraveler.wordpress.com/tag/townshend/
Now, after the LP is in the spining TT platter ( everything the same, including well matched cartridge/tonearm. ) the must critical issue is what happens once the cartridge stylus tip hits/track the LP grooves modulations.
The ideal is that those groove modulations can pass to the cartridge motor with out any additional kind of developed resonances/vibrations and that the transducer makes its job mantaining the delicated and sensible signal integrity that comes in those recorded groove modulations.
That is the ideal and could be utopic because all over the process/trip of the cartridge signal between the stylus tip ride and the output at the tonearm cable the signal suffers degradation ( resonances/vibrations/feedback ) mainly developed through all that " long trip " .
So, DAMPING IS NEED IT AT THE TONEARM/HEADSHELL SIDE OR NOT?
I'm trying to find out the " true " about and not looking if what we like it or not like it is rigth or not but what should be about and why of that " should be ".
I invite all of you analog lovers audiophiles to share your points of view in this critical analog audio subject. WHAT DO YOU THINK ABOUT?
Thank's in advance.
Regards and enjoy the MUSIC NOT DISTORTIONS,
R.
- ...
- 318 posts total
Dear @yeti42 : Unipivot tonearm designs are really sensitive and way unstable. I think that with your Aro you can get way better quality sound using the " tape " around its arm wand. This is a must test you need to do it. This other tape can helps you: https://www.homedepot.com/p/3M-Scotch-Super-33-3-4-in-x-66-ft-Electrical-Tape-6132-BA-10/100073402 this is a streched tape and this characteristc is the one that works the best. Very easy no take out with out any damage/sign into de arm wand. R. |
- 318 posts total