2. speakers
  3. 168704-76759

Casters to replace spikes

So I'm sure this will get a lot of challenge and flak, so please helpful comments only!

Long story short my focus has changed from home theater to two channel back to home theater.  Recently got a projector and in the midst of getting a screen (have a white sheet hanging as temporary) . On a whim I moved my Revel studio 2s and Voice 2 behind the sheet which improved the movie experience 1000%. However I had to push the speakers back against a wall, which is not ideal for two channel listening. I'm planning to purchase an electric screen so on occasion I'd like to be able to pull the speakers out from the wall with little effort when the screen is rolled up. Right now they are on the factory spikes sitting on Herbie's discs, so they can slide on the carpet with some effort. However, every time I've seen Wilson speakers in show rooms, they always seem to be on casters which made me wonder if that's a normal type of arrangement or at least a good enough arrangement.  my system is decent but my room needs lots of treatment so I'm taking an 80/20 approach here.  

Has anyone done this/ can recommend any type of solution for being able to move the front speakers with ease?  Thanks!
esthlos13
oldhvymec
5,101 posts
 
30 years I been preaching it.. Along with no BASS duty for valve amps and separating the BASS cabinets from the monitor cabinet.

I forgot phase plugs too. 20 years on those.. I’m even revisiting whizzer cones, too.. :-)

Springs are great they just need a good dampening agent like memory foam and paint the springs with silicone paint. Flex Seal works really good. Put ear plugs inside the springs and install them (No Bound style) it’s a BIG one up from stock No Bound.

On a 1 - 10 a NB is a good solid 5, with dampening added, 6.5-7, IF adjustable silicone/spring pods were a 10 (SOTA).

You can dampen the heck out of stock spring casters, the same way... Paint the springs and add shocks..

Regards
joenies's avatar
joenies
258 posts
 
My original B&W 801 E series speaker’s came with castors on them. Bought them new in 1982. They still sound great. I use them in my second  system for 2 channel and for HT. 
Ag insider logo xs@2x
yags1
41 posts
 
My B&W 801’s came with casters to mount in the speaker which I am glad they did
as when I clean my system it would be a bitch to move a 200 lb speaker by myself
and they were designed for the use of the casters
terry9
2,354 posts
 
Don't be misled by silly opinions, like "NO spikes".

If your speakers rest on a concrete floor, you can't do better than to couple the speakers to the floor as solidly as possible. Spikes lead to more adjustability than concrete bolts, so spikes are a definite alternative in such a case.

I have a rack of electronics in my HT, and it's on casters for reasons similar to yours. It can be made solid by screwing down 5/8" bolts through the bottom shelf to elevate it off the casters. Works fine, takes 2 minutes to make it ready to move, and two minutes more to anchor it.

You can easily do the same thing with a solid block like a maple butcher block. Four bolts, one on each corner (holes drilled and tapped for the bolts); 4 casters, one in the middle of each side. Just fix your speaker to the butcher block, and you're done.

But if your floor is wood, forget it. Locking casters will be better. IMO

Good Luck!
jrpnde
271 posts
 
   terry9 hit on a most important factor a bit. I have been challenged in this area as I have moved from one abode to another.....First, the location of your system. Is the floor solid, on the first or upper floor, or subject to vibration if only normal footsteps create distortion? Speaker positioning is, of course, important.
   Even though your floor is carpeted, carpet is not an end all to unwanted vibration. Just my 2 cents.


More to discover