Nobsound springs - load range

I'm curious about this idea of using foam ear plugs with the Nobsound springs.  I assume you roll the earplugs small and insert them in the middle of each spring?  Or is the idea to put them in the holes that don't have springs in them?

And is the theory that it further damps vibrations or that it provides lateral stiffening?

FWIW I have Nobsound springs underneath my 135 lb Moabs, 7 springs in the heavier front corners and 6 in the rear corners.  It works like a charm and even though A/B testing is impossible I would say there was some improvement in detail.

In the spring and there are few different colors to. Technicolor. :-)

I'm at 390 lbs before a 2" base a 2" bronze cap (optional) and a rear cabinet modification.

Hovering at 500 lbs. I'm going with pods in three spots. The main speakers and the  TT stand. Air Ride is sure looking good.. :-)

Regards

@ryder

I am using them without experimenting with removing springs (though thanks to this informative thread, I will-eventually) and my system sounds amazingly better than when I was using Machina Dynamica cryoed and heavy duty springs

As to experimenting, if you have any kind of blocks to replace each of the full set of 4 spring sets, removing them one at a time, will make it a lot easier.

Experiment with not putting them under the existing footers

hth

Some thoughts based on my experience meanwhile. I have Nobsound springs under my Streamer/DAC, my heavy mono blocks (44 kg each) and my Powerfilter unit. My initial attempt with the DAC (~12.5 kg) was with 3 units with 3 springs each, as this was the least number of springs per unit that I thought was stable in itself. This results in a situation where the Nobsounds don't  compress much. The hearing result was intimidating: added sharpness, less resolution and less dynamics. 

I then tried to use less springs and ended up with 4 units with 1 spring per unit. At least for the 12kg DAC this is still stable enough. On one side (where the transformers sit), I have two springs. In total this results in a situation where all units are compressed about equally and about 50% (gap of the unit compared to uncompressed, by rough eyesight). The acoustic result is great and I kept the springs since then: Instruments appear to resonate more freely, there is more room, and bass apears to reach deeper. The number of springs corresponds nicely to the rule of thumb mentioned in the OP (2.5kg per spring). For me this is helpful to determine at least a starting point for finetuning by listening.

For the monoblocks, the result of adding the springs is very similar and synergetic to the DAC. Under the power filter, the effect is the least. I would not claim that it would withstand a blind test, but I kept the springs there for optical reasons.

I really like the ideas of dampening the springs with foam ear plugs and/or PTFE tape. I will definitely try (on my DAC first).

I’ll keep this short although I have a lot to write. I am still experimenting with the number of springs on each footer. Patience would be required for this sort of exercise as there are many possible configurations from one to full seven springs with each footer, placed under the feet or chassis of the component, 3 or 4 units for each component etc.

I’m halfway through with the experiment on the integrated amp in the main system. The Nobsounds are placed directly below the component’s feet. In the Solid Tech brochure, 1-3mm gap is said to be optimal for the best sound reproduction. However, this is not the case with my system. Initially I tried 6 springs for all four Nobsound footers and this actually gave the best sound so far, although I later found that I need to reduce one spring each from the footers at the rear due to the unbalanced weight distribution of the component which is heavier at the front. I then reduced the springs to the minimum (3 springs at front footers, 2 at rear footers) and slowly got back up to 4 springs at the front, 3 at the rear, and I’m currently at 5 springs front, 4 springs rear. The current gap with this set up is 7mm which is slightly above 50% compression.

The sound got better when the gap got larger from 2mm to the current 7mm. I’ll add one spring to each footer tomorrow to get the gap up to 8 or 9mm tomorrow. I haven’t tried the full 7 springs but I think I may skip this one.

Improvements with an optimized set up include a sound that has better clarity, air and detail. The tone of instruments sounds more illuminated with a tube like glow. There’s more air between instruments which gave an airy feel and the bass sounds clearer with better definition and control.

I’ve briefly tried the Nobsounds on my Naim amps in the second system. As I don’t have much time to experiment, I didn’t do any adjustments to the springs. When placed on the preamp, I could not hear much difference. When placed on the power amp, the sound got worse. I then realize one cannot expect instant good results by installing these without much effort.

A note is the springs may not be in a perfect vertical position especially when using minimal springs ie. 1 or 2. The springs may be slightly inclined and this can affect sound quality too.