Replicant 100 stylus

raul, speaking about ''level of knowledge''. Your level of English is the

same as 20 years ago. Still not capable to produce one single 

decent English sentence and you dare  to speak about ''level of

knowledge''. 

Well I hope there are still a few Gyger S styli about as I’ve just had one fitted in place of a worn out Ogura PA.

Framer, in a recent review seemed to think the Replicant stylus was Swiss sourced.

I only have experience of the Replicant in it’s cheapest application, the SPU Royal N and if Ortofon are selecting their styli these will be the lowest grade. Still I preferred this cartridge to the PA equipped Proteus it replaced in my system and this is my reason to go for a Gyger for the rebuilt Proteus. Resale value isn’t a factor so I can indulge my curiosity.

yeti, We can't know what each retipper has in his stock. My friend Axel

Shurholz had ''some Gyger II '' in stock but was not willing to do

''stylus only'' retip. This was according to him much more difficult

than gluing the whole cantilever stylus combo in the joint pipe.

The joint pipe is an aluminum pipe in which front side cantilever

is glued and its back side coils and tension wire are fastened.

So actually all cantilevers are  HYBRIDE. That is to say whatever

material of the ''front cantilever'' the ''cantilever behind'' is aluminum

pipe. As JCarr explained in my other thread : Sony XL 88 D (D= diamond)

had an extra long aluminum part  so the diamond could be as short

as possible .That is why diamonds are only for the ladies ; to expansive

for man (grin). 

Well because  neither Gyger ( I, II and S)  is available in general there

is no sense to speak about their availability. They are not available

to all producers nor to retipers.

''Dissection'' of an fake intellectual. Every academic knows which

subjects are compulsory at high school. High school is obligatory

for university education. Well one need to read only 3 sentences 

produced by Raul to be able to deduce that he can impossible 

have high school education because English is obligatory subject

in each. This imply English grammar.

@rauliruegas as your direction of your very personal opinion, on a persons low levels of knowledge is very vague in determining who it was directed at, and at present, from my vantage point, it is looking like @mijostyn took the brunt of it.

I am very happy to declare ’I have  low knowledge levels’ when it comes to the most important design concerns for any product. I keep my knowledge levels limited by the end user, to allow for correct usage and learn what is required to make the product function, i.e, an item being, Passive, Key Wind Up, Battery, or Mains Powered Electricity.

The next once the above is properly understood, is considering how much input is required from myself to achieve the best function from the item selected to be used.

In the most basic periods of learning, I have come to understand it is best practice when I ’Don’t put the Electric Toaster powered by ( Mains Electric Power ) on a Maximum Time Setting and think it can be left unattended’, such a practice will be heeded when the Smoke Alarm ( Battery Power Supply and Strategically Placed as per manufacturers guidelines ) starts to function as designed. Not setting of the Smoke Alarm is also quite important for another reason, one of our Dogs has severe reaction to the alarm and it is not nice to a loved pet traumatised and the prolonged condition remains when the alarm is audible function of the alarm stopped.

In my case any my case only, I do declare that my low level of knowledge did enable the above experience to be encountered, but at the same time my low levels of knowledge have also allowed preventative measures to be put into action and there have been no reoccurrences.

A request can be put to myself for information about how devices have design concerns attached to them that need to be considered, and where asking for my understanding of these design considerations to be offered will be futile, as I can go on in the pretence that I am with knowledge, but this is not myself, I might comment, but not at any time would I reassure a person I am right with any information offered, it is not my skill set. I definitely would not pretend I had more knowledge than I have when it comes to HiFi and especially within the Sub Category of Analogue Replays. From my experiences within this forum, I think this is probably the case of nearly every contributor, who post within the raised threads in the analogue section of this forum, but I do suspect there are a few who do comment within the raised threads under the pretence that their knowledge is the most important consideration to be adopted, and then there is the very few forum members, that are quite odd in their individuality, who appear to avoid the subject content of the thread and add a contribution that it is difficult not to class as utterly rude toward another contributor to the subject within the thread.

Putting a focus on my low levels of knowledge into the world of the Phono Cartridge and then to the Sub Category of Phono Cartridges, such as a MC Phono Cartridge, both myself and a vast amount of users of these devices, have over time and from expressing an continued interest, have come to understand how to attach the device to a Headshell/Tonearm.

There are many including myself, who have learned the art of extracting the best from the device, by using specific geometries when setting the Interface between the device and supporting ancillaries. Through taking the time out to read the supplied information from the Producer about the Cartridge, the Cartridge end user can become versed in quoting a proportion of the Materials used for the Cart’s assembly and if a Cart’s is produced with the latest cutting edge technology available to the Brand for their design.

That unfortunately is low knowledge, it is a generalisation of the product, it does not incorporate any of the concealed IP around the Cartridge Design, that is the manufacturers concern only.

For a person like myself, does knowing the IP about the Cart’ make it any better a experience, for myself it is a no. Does knowing a description of the IP about a product and being able to comprehend it make me an authority with information that supersedes another’s shared experience with the same product, In my view definitely no.

I am interested only in how endearing the Performance of the Cart’ is to my unique preferences for a SQ and Sonic Signature presented within my system.

So I openly declare with all the above being followed by myself, I remain low in knowledge, but remain an individual with an inquisitive nature, and one who will happily converse with individuals who are very skilled with a Phono Cartridge Design, as well as being an individual who has historically had access to a unlimited introduction to a Producers IP and who has been involved in discussions abut the Companies areas of design concerns for my chosen Brand of Cartridge. I have been in correspondence about the parts used for the Cart’s assembly across the Brands Range, and how the parts are able to influence the presentation, this information has been freely discussed along with other options of Cantilever Materials and Styli that are not used by the Brand. That is the best I could achieve on the matter and am not in any further pursuit to gain further knowledge, I am happy and content to remain with my low levels of knowledge.

Being endlessly inquisitive, I would happily jump at the chance of encountering a demonstration of a Cart’ from the Brand that I am expressing a very long term interest in. .