Veneer delamination

     Perhaps a bit of background on a couple methods, used by various cabinet manufacturers, professional veneerers and common civilians use, in the application of veneers, will assuage some fears.

     The suggestion of using an iron tells me: Ohm applies theirs with one of the following, common methods.        

Hot Melt:  

https://www.hmtmfg.com/blog/applying-wood-veneers-quickly-using-hot-melt-adhesive/

and:  https://www.youtube.com/watch?v=X5PGXoigtD4

or: something similar to Titebond Wood Glue and heat:

https://www.youtube.com/watch?v=TxUKc4JWBaI

      As you can see from those vids; the judicious use of an iron would be an excellent method, for the repair of weak veneer adhesion.

     Seems to me: the high solids (rubber), 3M contact adhesives, we used back in the day, could probably be repaired the same way.    Never had to try it though.

     As suggested in the third link: keep the temps down to where you can touch the

surface of the veneer, without burning yourself.

     If that was the suggestion of the manufacturer; I'd have to assume, they feel whatever finish they applied, wouldn't be damaged, by the iron.

     From what I remember of the Ohms I repaired, back in the Eighties: they had a mostly natural, oiled finish (no gloss).   Don't know about now.

     I'd still use a lint-free cloth, between the iron and veneer, anyway.

     It's been my experience: in dry climates, in homes using wood burning stoves or high heat and no humidifier: glues dry out and expensive, antique furniture falls apart too (just a thought, having effected repairs on a lot).

     Give it a try, on one of the areas that is mostly out of sight, if you're afraid of the outcome.    ie: The rear seam would be a good place to start.

     Repairing one's own equipment, can be most gratifying.

     ie: Do a good job and you'll get warm fuzzies, every time you sit in front of those pretty Ohms.

@rodman99999 

Rodman is correct, a towel laid on the bubble and a warm iron should do it, lay it on for only a short 10-12 seconds and lift the iron and the towel should only be warm, do it several times, no rushing it, and it should remelt the glue, press down hard with a block of wood or a book as it cools down and it will make it lay flat.  If you are not a do-it-yourselfer, any local Denver woodworker/ cabinet maker should be able to do it for you, as you are not looking to re-veneer it, just fix the area that popped. Can happen with any furniture with a veneer.  

Dry air can cause issues with shrinkage and delamination all real wood finishes require furniture oil. If poly coated just toss them who wants plastic over real wood?

@dbwinters , They are using a heat set glue. They either did not heat it well when they put the veneer on or they did not use enough glue. This is not that hard!!

Make sure the bottom of the iron is perfectly smooth. If not smooth it with 2000 grit silicon carbide wet or dry paper and use water or use 4-0 steel wool. Set the iron to the middle of it's temp setting. You should be able to tap the bottom without burning yourself. Where there are bubbles prick the center of the bubble with a sewing needle (to let the air out). Then place butcher's paper over the area and slowly pass the iron back and forth over the area, pressing down firmly for one minute. 

If the veneer does not stay down they did not use enough glue and the speakers are defective. They should send you a new pair and return shipping labels for the defective speakers. I assume the speakers are still under warranty. If they do not want to do that tell them you want a complete refund, go buy something else and plaster them on the net. Errors are a fact of live. It is what a company does with it's errors that counts, particularly in these days of the internet.