What is the science behind audiophile fuses?


There were many threads on the topic of "audiophile fuses" on this forum, and I sure don't want to open old wounds and trench warfare. The fuse on my preamp blew suddenly two days ago, which prompted me to search for a replacement. That's when I came across the term "audiophile fuse" and the fact that they demand far-out prices. Deeper curiosity brought me to several other fora, where users posted glowing praises about their Zero fuses and other exotica. Now I am a scientist, but not a physicist or electrical engineer: so please enlighten me! How can a fuse have an audible influence on the signal, when the signal does not even pass through it? How can a fuse be "directional" when it deals with alternate current? I mean, if I recall my university physics, a fuse is basically a safety valve and nothing more. Am I completely missing an important point here? My scientific field is drug discovery, and because of this background I am thoroughly familiar with the power and reality of the placebo effect. I that's what I am seeing here, or is it real physics? I need objective facts and not opinions, please. I really appreciate your help!

 
128x128reimarc

@carlsbad2...when you mentioned 'slug', 1st thought 'metal bar, low gauge copper'; 2nd, a diy from an earlier 'confounded fused flail' that 'appeared' (not sounded, yet) worth spending less time on than you do...

But I applaud your efforts to fab and take a Good Slug @ it... aesthetics do count even for a lowly slug... ; ) đź‘Ť

3urd was 'homeless snail', soon to be ' budget escargot' ='d *bleah*🙄

@reimarc ....If 'lectric exotic at the super bunting autopsychoic sounds like fun:

0>60 under 2, 0>100>0 under 8 ; seconds, street version pending if not out already... 

The budget 2 wheel version:

...all it lacks is 110db air horns....  My 1st personal diy option...; )

@reimarc The power supply doesn’t merely allow proper operation, it is that which is the source of the actual music. Simply put, the amplifier circuitry modulates the flow of that power through the speakers. Ceteris paribus, the better the power supply, the better the sound.

not the signal circuit itself but the part that supplies the power for proper operation.

I don’t know how to make a good sounding fuse, but I have discovered that a cracked fuse holder can make most any fuse sound bad.

If a system is intended to be used at a level well below its capabilities to deal with current, then it makes building the fuse easier, it would seem. The fuse can be set to pop at a much, much higher current level than any normal listening session would produce. So the fuses internal resistance and any audible compression effects from the fuse beginning to heat can be minimized. I used to have some piezo compression drivers that had little light bulbs in them that acted as fuses of sorts. Instead of blowing, they would take to glowing, which would effectively compress the output to the tweeter. This is fine for a PA system but probably not acceptable to most HiFi enthusiasts.

Doesn’t the power supply include capacitors that store electrical power used by the device, including the capability to supply power for peak demands?  Shouldn’t the power supply be designed so that the current draw through the fuse should never exceed the rated value under normal use?  Otherwise, it would seem the power supply is under designed.  I believe some may be putting too much emphasis on the role of the fuse in the power supply chain.  Obviously, it is essential but, as long as it works properly, perhaps not a direct influence on the sonic end result?

Cleeds...I have extensive personal experience with fuses, including testing a pile of Synergistic Research fuses a few years ago...they were useless and risky (inaccurate  current ratings) junk then, and still are silly and expensive nonsense. Quantum my a**. Call Nelson Pass or Dennis Had to discuss it further. If "magic" fuses actually did what they claim, everybody get on board with 'em....they don't and we're not.