The approach of one anal analogist (VERY LONG)
----
I was asked to post this in this thread, so I will do so.
OK, I will make a very brief visit here and offer some tips that I have picked up myself and have learned from others over the years. They may or not prove useful to you. It is fine to use less exotic methods and solutions for cleaning your LPs but, in the end, if you decide to acquire more and more vinyl and you want to do the best job possible, obtaining a vacuum cleaner and using quality solutions of some sort is a very effective INVESTMENT. Many, though not all, of the methods commonly suggested do little more than push old dirt and grime around and around in the grooves, not cleaning, and possibly doing serious collateral damage. On the other hand, a vacuum cleaner will lift out this grime, in solution, and carry it away. It is also difficult to rinse sufficiently based on the usual suggestions, with a residue and sonic signature left behind.
I will detail my record cleaning regimen. Mine is basically a two-part process, depending upon the filth of the LP. Use any of what seems to make sense for you. Or, ignore it all!
PART ONE SINK CLEANING
The first part of my regimen is used for any record that has come from a flea market, Goodwill, etc., or a record that has not been played in years and there is some question as to dirt and dust in the grooves. This first part could be employed as a total cleaning method if one decided not to obtain a vacuum machine.
There are a few necessary things you will need:
A pan to hold solution one of those 6X12 metal or glass meat loaf pans works well. I would suggest a dedicated pan for this. If you use it to cook in, there may be residual grease left behind.
A lint-less terry cloth towel or other cotton cloth for drying.
A brush for cleaning. Go to the Home Depot, Lowes, or whatever, and buy one of those very soft painting pads with a handle. These have a flat base about 7 wide. Be sure to get the one with the foam pad inside that has a very fine and soft cover on the outside. DO NOT use the ones that are foam only. They usually are packaged as fine, medium, and coarse, depending upon the painting intended. For THIS purpose the coarse works the best as coarse as that might sound! :-) These can be had for about $6-7 and will be the only pad you will need. They are almost the perfect width to span the recorded area of the LP, have a comfortable handle, will NOT scratch, and are easily rinsed and cleaned when you are finished. If you are anal, get two one for washing and one for rinsing.
A slightly stiffer brush for cleaning stubborn spots. A stiff bristled paint brush or a carbon fiber brush works well for those small spots of guck that you will often find on a used LP like when someone has placed food-laden fingers or other unmentionables on the vinyl.
A GROOVMASTER. I find this to be an indispensable tool for hand cleaning records. There is a guy in Massachusetts who sells these on E-Bay. Just go there and search under groovmaster. It will cost you $25-35 depending on bidding but is worth its weight in gold. You could probably make one, but buying one is easier. The Groovmaster is basically two acrylic discs, each with recessed circular grooves that contain rubber o-rings on both sides. These discs have a threaded rod that runs between them with handles on each end. One side of the discs is for LPs (larger o-rings), the other for 45s (smaller o-rings). You put one disc on each side of the record and then screw the handles together. This tool provides ultimate security against getting fluid on the label you can hold the records straight under running water. Plus, it provides a handle so that you neednt ever touch the vinyl with fingers while cleaning. HIGHLY RECOMMENDED. I only wish I had the patent on this device.
A dish rack (optional). Use any of the many racks designed for dishes to be placed after washing. Use one that is rubber/plastic coated and has the little channels for holding plates in an upright position.
So, now begins the cleaning. Take your loaf pan and put JUST A SMALL SQUIRT of mild dish washing detergent in the bottom (I use Dawn because it has a grease cutter). Then fill with just warm water and mix. Place the Groovmaster on an LP. You will now have a round handle from which to hold the record. Turn on the faucet so that the water is just warm, not hot. Give the LP a thorough rinse without using any brush use your spray head if you have one. Then, dip the paint pad in the soap/water solution to get it good and wet. Make a single circular pass around each side of the LP, following the grooves and using light pressure. If you want you can let the soap/water solution soak on the LP for a minute or two. Then rinse the LP and the pad. Now, dip the pad back into the soap/water again and, using more firm pressure, work your way around one side of the LP in short circular (with the grooves) scrubbing strokes, following the grooves around the record. When youve made a full circuit, rinse the pad, redip in soap/water, and repeat on the other side of the LP. Follow with a THOROUGH rinsing of the LP under the faucet. Use a spray head if you have one. Here, you can also use an additional paint pad to help with the rinsing if you remember to rinse it completely after each side. I find that I do not need to do this using a spray head.
If you have a very stubborn spot on an LP, you can give it particular attention. I have made a solution containing 3 parts water and one part DIRECT vinyl tile cleaner. Or, better yet, use Record Research Deep Cleaner. Put the solution in a spray bottle, spritz the affected area, and let it soak awhile. Use the stiffer brush to then gently remove the gunk. Some have said that using an old water pick with this solution also works well. I have even heard of people using wood toothpicks to carefully run with the grooves to remove gunk. Whatever the method, make sure to carefully rinse when finished. Now, some will hold that you should use distilled water as a final rinse because tap water can leave residue. I do not do this because I follow up this cleaning on a VPI machine. If this is the end of the cleaning for you, the use of distilled water as a final rinse might be in order.
After both sides of the LP are cleaned and thoroughly rinsed, remove the Groovmaster and carefully lay the LP toward one end of a large towel that you have spread across a firm flat surface. Fold the towel up over the LP to make it a sandwich. Then, use light pressure to blot the LP with the towel. When mostly dry, place the LP in the dish rack until dry or until you are finished cleaning other LPs. There may still be a hair of lint or two on the LP when finished. If so, use a carbon fiber brush to clean the surface of lint. Then, place the LP in a new, CLEAN inner sleeve of your choice. At this point, try the LP on your rig. If all sounds quiet, thats it. There are times when two or three cleanings are needed. Dont give up on an LP if there is still some noise after the first pass. But, if a couple or three of cleanings dont do the trick, assume groove damage and get another copy. All of this effort will depend on what level of noise you are willing to accept, how easily the LP can be replaced, the value of your stylus, etc., etc.
PART TWO VACUUM CLEANING
I use a VPI 16.5 as a follow up to STEP ONE for records that started out as very dirty and as the only step for new or relatively clean LPs. The use of this RCM or any of the others is pretty straightforward, most choices being limited to the fluids used. Personally, I do not like the alcohol-based solutions and have found through MANY trials that the Record Research products are the best in terms of effectiveness and for not leaving a sonic signature behind. I use Record Research fluids, only. I buy the Deep Cleaner (16 oz. - $25) and the Vinyl Wash (32 oz. $25). Never been able to find it cheaper but would love to hear of cheaper sources!
The following assumes a hand cleaning RCM, not the VPI 17, where the cleaning and vacuuming is done by the machine, itself. These machines are great and recommended, though. I just couldnt cough up the $1K when I bought my used VPI 16.5!
I begin by placing the LP on the platter and screwing down the knurled, threaded keeper. As a side note, I always begin with Side A(1). It may seem silly, but if you are cleaning a number of records and have kids coming in, the phone ringing, etc., it is easy to forget whether you have done one side or another.
First, I apply some Vinyl Wash (VW) to the leading edge of a Discwasher brush (the one with wooden handle and attached pad). Turn on the machine and apply the VW to the LP to collect any small amount of lint or dust and to thoroughly wet the vinyl (recommended before applying the Deep Cleaner (DC)). While still wet, I use a carbon fiber brush to apply DC to the LP and give it a good two or three cleaning spins. While the LP is usually free from serious grunge after STEP ONE, or if new, the DC assures that any mold-release agents are expelled. After the DC is applied, I give the LP one or two vacuum spins.
Then, I like to give the LP a first rinse using the VW on a clean, separate LAST pad. I like the LAST pad better for the rinsing as I think the cleaning has been done and I am not as concerned about getting to the very bottom of the grooves in this step. I apply a generous squirt of VW and give it three rinse revolutions, followed be one or two vacuum spins.
Finally, I repeat this process using another separate LAST pad with a little less VW and then three vacuum spins to get the record good and dry. A little caution here is necessary. The VPI manual states that you should not do too much dry vacuuming so as to avoid record damage and/or static buildup. Let your good judgment be your guide in striking a balance between this and assuring that the record is dry. When satisfied, place the LP in a clean record sleeve.
One note, I always remove the vacuum wand assembly and use the open hole to vacuum the wand strips and all cleaning pads after each LP.
One can also try to clean inside of old covers if they contain a lot of dust. Holding the cover upside down and tapping on the spine will do a decent job. If you want to go crazy, I have used an old thin, flat upholstery tool on my vacuum cleaner that I drilled a series of holes along its length. Just be careful not to damage the spine or seams.
There are two other steps than can be done if you want to spend the money and feel it is effective. One is to use LAST Record Preservative easy to apply while the LP is on the platter AFTER cleaning. The other is GruvGlide which can be applied easily at this point, as well. I will not enter into the debate regarding the merits of either product here, though. To each his or her own on this one!
Cost? I can do about 200 LPs with the Record Research cleaners. That comes to about two bits per LP. The painting pad cost me $7, the Groovmaster $32, the Discwasher $17, the LAST pads $20, the VPI 16.5 $375. I have cleaned just over 900 LPs using these materials about 50 cents per record with the marginal cost decreasing each time I clean another record. Add another 25 cents for an inner sleeve and we are talking, roughly, $1 per record.
There are MUCH cheaper methods than this, I will grant to you. If you decide to brew your own solutions and/or eschew a RCM, you can get off for much less. However, this method works for me and VERY RARE is the case that I have even minimal surface noise when following this routine. Hope this is of help to someone, anyone!
BTW, I would be remiss when discussing Record Research products if I did not mention the #9 stylus cleaner. It is THE best product for cleaning styli, IMHO.
