A wee bit off topic here, but I have a factory built MKIV. Over the years the springs have compressed and finding it difficult to replace them. VPI no longer has replacements or the sorbothene replacements. I know can insert neoprene tubing into the center of the springs to correct. But would like to get other ideas on a remedy. Anyone have suggestions?
VPI HW-19 Upgrade question SAMA or SDS?
OK, the upgrade bug has bitten again, and I know that ther are a number of folks here that have lots of experience with their HW-19.
I have a VPI HW-19 Mk III that I recently upgraded to a Mk IV with a TNT platter with an inverted bearing. Also, it has a sorbathane puck suspension rather than springs, and I've replaced the rubber feet with cone type spikes. The table dead level sitting on top of a 1-1/2"-inch thick maple top shelf of a very heavy flexi-rack. I'm using an ET-2 arm connected to my shop compressor with four stages of precision air-regulation with the final stage adjustable just before at the entering the ET-2. I just air-up the compressor's 30 gallon tank, then kill the compressor so that it won't start back up, and I can listen for hours (wife think that I've lost my mind every time that I do this, but that's another story). Also, I'm currently listening to an AT33PTG that I have come to really like. The phono section is a Threshold SL-10 upgraded with Black Gates throughout.
The Mk IV upgrade made a real difference from the Mk III. As I quickly found out, the Mk IV presents a fuller soundstage and better base than the Mk III platter/bearing. I view that upgrade as well worth the money, especially buying it used here on A'gon.
Here is my dilemma with funds being limited to purchase only one or the other at this time, but not both - at least for now.
What do you think would be the best upgrade for this HW-19? A new SAMA for $400, or a used SDS for $600 to $800? Used SAMAs never seem to come up for sale, but you can always find a used SDS on Audiogon. I think that there are at least three available for sale here as I write this.
Also, if someone thinks neither mentioned upgrade would be cost effective, and that money would be better spent with an upgrade elsewhere, please say so. I'm trying to keep my mind and ears open - for better sound!
Thank you!
I have a VPI HW-19 Mk III that I recently upgraded to a Mk IV with a TNT platter with an inverted bearing. Also, it has a sorbathane puck suspension rather than springs, and I've replaced the rubber feet with cone type spikes. The table dead level sitting on top of a 1-1/2"-inch thick maple top shelf of a very heavy flexi-rack. I'm using an ET-2 arm connected to my shop compressor with four stages of precision air-regulation with the final stage adjustable just before at the entering the ET-2. I just air-up the compressor's 30 gallon tank, then kill the compressor so that it won't start back up, and I can listen for hours (wife think that I've lost my mind every time that I do this, but that's another story). Also, I'm currently listening to an AT33PTG that I have come to really like. The phono section is a Threshold SL-10 upgraded with Black Gates throughout.
The Mk IV upgrade made a real difference from the Mk III. As I quickly found out, the Mk IV presents a fuller soundstage and better base than the Mk III platter/bearing. I view that upgrade as well worth the money, especially buying it used here on A'gon.
Here is my dilemma with funds being limited to purchase only one or the other at this time, but not both - at least for now.
What do you think would be the best upgrade for this HW-19? A new SAMA for $400, or a used SDS for $600 to $800? Used SAMAs never seem to come up for sale, but you can always find a used SDS on Audiogon. I think that there are at least three available for sale here as I write this.
Also, if someone thinks neither mentioned upgrade would be cost effective, and that money would be better spent with an upgrade elsewhere, please say so. I'm trying to keep my mind and ears open - for better sound!
Thank you!
- ...
- 34 posts total
- 34 posts total