Digital XLR vs. Analog XLR - Balanced Cables

Ckoffend-

You can try them; they should work. You have nothing to lose.

OTOH, I would be more certain that digital cables would work for analog.

Kal

The only thing about cables that is going to make any difference as to jitter is whether the cable has sufficient bandwidth so as not to cause jitter due to the inherent characteristics of the data signal itself. Even then there should be correction circuitry at the converter stage to correct for any transmission induced jitter. Likely, the analog and digital versions of the XLR cables both exceed the bandwidth necessary to avoid transmission induced jitter.

Here is the quote from Stereophile article "A Transport of Delight: CD Transport Jitter"

"While we're on the subject of the digital interface, I should point out that the engineering for transmitting wide-bandwidth signals was worked out nearly 50 years ago in the video world. In video transmission, the source has a carefully controlled output impedance, the cable and connectors have a precisely specified characteristic impedance and are well-shielded, and the load impedance is specified within narrow tolerances. If these practices aren't followed, reflections are created in the transmission line that play havoc with video signals. This issue is so crucial that a whole field called Time Delay Reflectometry (TDR) exists to analyze reflections in transmission lines.

The audio community should adopt the standard engineering practices of video engineering for digital interfaces. This means designing transports with a carefully controlled 75 ohm output impedance, precisely specified characteristic impedance of the cable (75 ohms with a narrow tolerance), and junking RCA connectors in favor of true 75 ohm BNC connectors. By applying standard video engineering techniques—in use for decades—the high-end product designer can greatly improve the performance of the transport/processor interface. We've seen what happens with a poorly implemented interface with the SV-3700 and different cables: higher jitter in the recovered clock and degraded sound quality. The engineering needed to optimize the digital interface is readily available. Let's use it."

As far as I know bandwith of the cable determines losses in the cable in dB/ft while jitter is strictly property of mismatched characteristic impedance (SQRT(L/C)). Antena/video 75 ohm cables might have different losses (RG59, RG6, RG11 etc) but won't create reflections as long as they have exact 75 ohm. Please correct me if I'm wrong.

Kijanki, I hear you. But one of my concerns is with many of these cable companies is when does the marketing end and the real engineering begin. Even with digital cables, there are certainly some cable manufacturers who clearly point out that the cable is a "true 75 ohm" or "true 110 ohm" cable while many others just call the cables digital cables.

Ckoffend - I would say that most, if not all, digital cables have particular targeted characteristic impedance - in case of audio 75 ohm for unbalanced and 110 ohm for balanced. But just look at typical 75 ohm video coax - it is so much different than analog cable. First of all analog cable uses separate wire for the ground. Carrying ground thru shield is really bad idea and grounding shield at both ends is even worse (XLR is but it was mistake). Metal is important only on the surface (plated) because of the skin depth at these frequencies. Lower dielectric constant is important but not as much as in analog cables. Dielectric constant of polyethylene, most likely used in digital cable is 3.3 while foamed teflon is getting close to 1.5 (and oversized air tubes can bring it even bit closer to 1)).

I understand the need for exploration and experimentation but when I buy cooking oil I am not tempted to try motor oil instead just because there is zero cholesterol and no saturated fat in it(and no other parameters to differentiate them). It was designed for the car and I have no reason to question it. It is a matter of taste, so to speak, but we can get easily lost here since changes between cables are very small. Going by the book shields us from many mistakes.
Jitter will transfer from time domain as a noise. It won't change the sound other than making background less black. That was what I noticed with jitter rejecting Benchmark. Its jitter bandwith is in order of few Hz and at frequncies of interest (kHz) gives -100dB rejection of the noise that was at -80dB to start with - practically complete rejection. Cables here don't make any difference - similar with your Purcell but if you have instead of upsampling DAC oversampling DAC or even NOS DAC than digital cable will make huge difference.

There is an excellent article in Stereophile (available on line) on the jitter explaining how sidebands are created, why they are audible and showing everything in numbers with typical transport/CD. Just educational - you can use any cable with Purcell (if I understand it right)