Lightspeed Attenuator - Best Preamp Ever?


The question is a bit rhetorical. No preamp is the best ever, and much depends on system context. I am starting this thread beacuase there is a lot of info on this preamp in a Music First Audio Passive...thread, an Slagle AVC Modules...thread and wanted to be sure that information on this amazing product did not get lost in those threads.

I suspect that many folks may give this preamp a try at $450, direct from Australia, so I thought it would be good for current owners and future owners to have a place to describe their experience with this preamp.

It is a passive preamp that uses light LEDs, rather than mechanical contacts, to alter resistance and thereby attenuation of the source signal. It has been extremely hot in the DIY community, since the maker of this preamp provided gernerously provided information on how to make one. The trick is that while there are few parts, getting it done right, the matching of the parts is time consuming and tricky, and to boot, most of use would solder our fingers together if we tried. At $450, don't bother. It is cased in a small chassis that is fully shielded alloy, it gets it's RF sink earth via the interconnects. Vibration doesn't come into it as there is nothing to get vibrated as it's passive, even the active led's are immune as they are gas element, no filaments. The feet I attach are soft silicon/sorbethane compound anyway just in case.

This is not audio jewelry with bling, but solidly made and there is little room (if any) for audionervosa or tweaking.

So is this the best preamp ever? It might be if you have a single source (though you could use a switch box), your source is 2v or higher, your IC from pre-amp to amp is less than 2m to keep capaitance low, your amp is 5kohm input or higher (most any tube amp), and your amp is relatively sensitive (1v input sensitivity or lower v would be just right). In other words, within a passive friendly system (you do have to give this some thought), this is the finest passive preamp I have ever heard, and I have has many ranging form resistor-based to TVCs and AVCs.

In my system, with my equipment, I think it is the best I have heard passive or active, but I lean towards prefering preamp neutrality and transparency, without loosing musicality, dynamics, or the handling of low bass and highs.

If you own one, what are your impressions versus anything you have heard?

Is it the best ever? I suspect for some it may be, and to say that for a $450 product makes it stupidgood.
pubul57
Perhaps the reason some of you are reporting sonic differences between using battery power and the wall wart is simply that volume levels haven't been precisely equalized for the comparison?

I realize that the LSA has an internal regulator, but no regulator is perfect, and so perhaps voltage differences between the outputs of the battery and the wall wart result in slight (fraction of a db) changes in attenuation, that need to be compensated for with the volume control.

To totally rule out the possibility that the sonic differences are attributable to volume changes, I believe that the levels should ideally be equalized to within around 0.1 db, which is probably impossible to do without instruments.

Best regards,
-- Al
Al, that really makes sense. And it seems to explain Clio9s experience, something different but hard to put your finger on it.
Al, if the voltage output of the battery and wall wart power supplies are both 12VDC does that change anything in your last post?
Anthony, no, I was assuming in my last post that both supplies are nominally 12VDC. However, neither is likely to be exactly 12VDC, and the two are not likely to be exactly the same. Also, the output voltage of the battery will change slightly as it discharges.

While the significance of those differences will be greatly reduced by the internal voltage regulator, as I said no regulator is perfect. So it seems conceivable to me that if the power source is changed but the volume control setting is not changed, there could be a tiny change in volume that would be subjectively perceived as a sonic difference.

Best regards,
-- Al
Sorry guys the internal regulator in the Lightspeed Attenuator is 5v and will be the same regulator regarless of using battery or mains, so ther is no difference in voltage that the LED's are seeing not even a miniscule of a volt.
Cheers George